a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa

Q: Q2: A composite component consists of a glass fiber and an epoxy matrix. The glass fiber weight…

A:

Q: 2. An axial rod made of three different materials is fixed between two walls. (You can do this…

A: Given data:   E1 = E =10 MsiE2 =20 MsiE3 = 30 Msiα1 = 10 x 10-6 /°Fα2 = 20 x 10-6 /°Fα3 = 30 x 10-6…

Q: A brass wire with Young's modulus of 92.0 GPa is 1.88 m long and has a cross-sectional area of 5.00…

A:

Q: Aluminum bolts 2cm in diameter and 500cm long are used to hold the head on a pressure vessel. One…

A: Given:The diameter of the bolt is .The length of the bolt is .Sensitive extensometer measures…

Q: TA 500 Ib buoy, with a 2 ft radius is tied to the bed of a lake using a steel cable. What is the…

A: Mass of the buoy = 500 lb Need to determine the tensile force in the cable.

Q: 1.The height of the Washington Monument is measured to be 170 m on a day when the temperature is…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: Q2. Determine the young's modulus of elastici following test result on a steel rod: = 25 mm Rod…

A: Given Data⇒ Rod diameter(d)=25 mm=0.025 m Rod length(L)=150 mm=0.15 m Maximum applied load(F)=300 KN…

Q: Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional…

A: Trusses are constructions made solely of components with two forces. Each truss member is believed…

Q: a) The stress in the wire. Answer in MPa b) The strain in the wire. c) The increase in the length of…

A:

Q: 30 MPa 20 MPa 50 MPa 50 MPa 20 MPa 30 MPa What is the radius of the Mohr's circle for the element…

A:

Q: A liquid compressed in a container has a volume of 1 liter at a pressure of 1MPA and a volume of…

A: Bulk modulus is given as = hydrostatic pressure/(change in volume/original volume)

Q: 1.5 m 1.0 m A B 3.3 m FIGURE P1.10 C 15 kN 12 kN

A: Considering that you want to know the forces in the members.Thus the reaction forces are as shown…

Q: 1.0p 1i 1860N 0,1 003 ab Answer EMC = De balk van 148 kg wordt gedragen door twee klemmen. Eén zo'n…

A: given; a=0.1mb=0.03m mass(m)=148kgweight(w)=mg                   =148*9.81…

Q: A round solid bar has a diameter of 30mm. A tensile force of 120kN is applied at the centroid of…

A: Calculated stress in the bar and sketch the stress distribution through its thickness.

Q: HaW: Find the tensian force in each eable. 35 木 A. oss م لملعنه سسلمیڈک the pully te Kep the system…

A: 1) Solution: Consider joint 1 Considering system in static equilibrium,…

Q: The diameter of the large piston of a hydraulic jack is found to be 75 mm. A force of 58 N is…

A: Given that, Diameter of large piston, D2=75 mm,Force applied of small piston, F1=58 N,Load lifted by…

Q: A pressure vessel has a wall thickness of 8mm and a diameter of 300mm. What is the circumferential…

A:

Q: Don't use chatgpt. Need in hurry (Add FBD)

A:

Q: 1. Mean diameter D, inside diameter Din and spring index 2. The expected stress at the operating…

A: We are to determine the dimensions of the spring and the expected stress and deflection of the…

Q: Given the image below, what is the magnitude of the equivalent concentrated load of the weight of…

A:

Q: 60° looks 50 g C 80° 6 G 30 VO 38 66 f 7 ft 78 ) ។ Yo >15 3ft 4ft 2ft Find force for all member? E

A:

Q: 4. The timber member has a cross-sectional area of 1750 mm and its modulus of elasticity is 12 GPa.…

A:

Q: In dead weight tester, the applied load is 0.017 kN, theoretical pressure is 150 kPa. Then the area…

A:

Q: A 6.8kg cat is standing on a uniform beam that weighs 245.0 N. The beam is supported by a hinge…

A:

Q: A cylinder has a pressure of 25 MPa and the load on it is 10750 Ibf. Find its diameter in mm. 43.2…

A: Given that A cylinder has a pressure of 25 MPa and the load on it is 10750 lbf. Find its diameter in…

Q: A metal plate has a consistant thickness of 50mm and is acted upon by 4 co-planar forces. Calculate…

A: Given:

Q: The tensile modulus of a 0°, 90°, and 45° graphite/epoxy ply is measured as follows to give E1 =…

A: Solution: Given Data: E1=26.25 MsiE2=1.494 MsiEx=2.427 Msi   To Find: (a) Value of Ex for 30o ply.…

Q: What is the force required to a steel wire to double its length when its area of cross-section is…

A:

Q: Q2: A spacer is turned from Aluminum alloy with elasticity modulus of 78 GN/m?. The spacer has a…

A:

Q: Strengon of Mate "as Pressure este Question The hoop stress on the walls of a thin cylinder is 42…

A: Hoop stress Diameter d=84 cm=840 mmThickness t = 1.5 cmTo Find-The internal pressure of the…

Q: A solid spherical material made of rubber with was exposed to a change in pressure of 85 Pa. Its…

A: Given Data :- Change in pressure = 85 Pa Volume Reduced (Change in Volume / Original Volume) = - 8%

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A:

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. Z. 2 ft 4 ft 4 ft…

A:

Q: When rebuilding his car's engine, a mechanic must exert 300'N of force to insert a dry steel piston…

A:

Q: O = 1024 KG/CM² FIND THE DIAMETER OF THE BAR THAT VWILL BE STRONG ACCORDING TO THESE COMPONENTS OF…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.