Answered: 2- A 208 V, 60 Hz, 4 pole, three phase…

2- A 208 V, 60 Hz, 4 pole, three phase induction motor has a full load speed of 1755 r.p.m. Calculate its synchronous speed, the slip and rotor frequency

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Related questions

Q: How to draft this circuit digram in a breadboard?

A: The given circuit diagram is shown below.

Q: i) ii) R(s) 5 G₁ G₁ G₂ G₁ G 10 -Y(s) Figure 4. Use the block diagram reduction technique to…

Q: 2. Determine the voltage , across the 20-12 resistor. 15 V 4011 www 1502 www 2002

Q: 2.) What is the decimal equivalent output of the register shown in the figure below +5V pos 4 LSB…

Q: A buck-boost converter has an input voltage of 12 V and the duty ratio is adjusted to 0.5. What is…

A: Given: A buck-boost converter has, Input voltage, Vin=12 V. Duty ratio, D=0.5.

Q: Q3) Using the superposition theorem, find the current, voltage and the power dissipated through R₁…

Q: Refractive index of glass is 1.5. Find the wavelength of a beam of light with a frequency of 1014 Hz…

A: Solution !!

Q: Consider the system below: Load X ZKX Y Capacity [MW] 51 248 201 B Generator X1-3 = 0.4 p.u. PMAX…

Q: The National Electrical Code (NEC) covers the safe and proper installation of wiring, electrical…

A: NEC requirements:- According to the NEC, a circuit's conductors must be enclosed in a raceway,…

Q: Three bulbs arranged in series connection are each 6 volts. The current flowing in the circuit is I…

Q: Q2) Using the nodal analysis, find the node voltages V₁ and V₂, then find the power dissipated in…

A: Apply KCL at node and and node 2 and using ohms law write the two equations in terms of node…

Q: With the given circuit below, find the value of iL at t=12ms. Write the final answer in Amperes (3…

Q: With neat sketch explain working of van de Graff generator Note : strictly no copy paste…

A: It is asked to sketch and explain the working of Van de Graaff generator.

Q: Consider Figure AA. Solve for VG if VDD = 23 V, R1-6.8Mohms, R2-3.8Mohms, RD=2.7kohms, and…

A: Given: An enhancement type MOSFET with voltage divider biasing. VDD = 23 V, R1=6.8 MΩ, R2=3.8 MΩ,…

Q: If R1= 1 Ohm R2= 2 Ohm. Suppose R1 and R2 are connected SERIES. Then what is Equivalent (a)10 Ohms…

A: Given data, Resistances are given, R1=1 Ω, R2=2 Ω.

Q: 12. Draw the Timing diagram for INR M. > Fetching the Opcode 34 from the memory 4105H. Let the…

A: Solution !!

Q: An 8085 microprocessor executes "STA 1234H" with starting address location 1FFEH (STA copies the…

A: Solution !! Given STA 1234 HStarting addressing location is 1 FFEH1FFEH: STA 1234Hi.e. 1FFEH : XX…

Q: Given the dc servomotor and load shown in Figure P3.10, represent the system in state space, where…

A: The mechanical system is given as Now the torque developed by the motor will…

Q: In a huge or large capacity rating alternators, the moving part is

Q: 18V- 9Ω www. 8Ω Μ 12Ω 18Ω 11Ω www 5Ω ΖΩΙ ΜΕ ΠΩ 3Ω Μ ΠΩ ΕΣΤΩ 5Ω

Q: Given the following circuit where Vs = 10, IT = 15 mA, and P₂ = 42.7 mW, find P₁, the power…

Q: Determine VI and V₂ using nodal analysis V₁ 5012 V2 5A1 400 3029A

A: We need to find out node voltage for given circuit by using of nodal analysis .

Q: A 3-core cable (3-Øline) transfer 33 kV and 50 Hz, If the conductor-earth capacitance (Ce) is 0.23…

Q: The voltage applied to a circuit is: v = 215 sin (377t)- 140 (cos 754t) + 70 sin (1131t) And the…

Q: Consider the circuits in the figure (a) Assume R=600. 4 V +1 R 40 92 60 92 Find /

A: Given, The circuit is, Where resistor R=60 Ω.

Q: Solve for VGs of an EMOSFET if VG = 6.44 V, VGSTH=3V, IDON=5.8mA, VGSOFF=5.7V, and Vs=1.22V.

A: Given: VG=6.44 Volts, VTh=3 V, IDon=5.8 mA, VGSoff=5.7 V and VS=1.22 V.

Q: 8 IK TR 4K Find V. = ? ww um 2K 6K m Зік me 4K 3K V₂K²?

A: Here as per the honor code only the first question is solved. Please post the rest seperately.

Q: Q5) Find the Thevenin equivalent circuit for the network in Fig. 5. Then, under the maximum power…

Q: ns In the following circuit, Vdd is power, Vss is ground. What function is Vout? C Vout O Vout OR…

Q: R1 P2 find the current P3 13

Q: These are laminated steel core containing current-carrying copper wires; and in general if it is the…

A: We need to select correct option for given statement regarding Motor parts.

Q: Given the empirical diode junction equation V = nV, In with VT = 26 mV, Is = 3.9x10-15 A. Determine…

A: Given, Diode voltage VD=nVTlnIDIs VT=26 mV Supply current Is=3.9×10-15 A

Q: a. b. 1. find the total solution to the problems d²y 5dy t d₁² dt +6=t 1²y 6dy + +9=te-¹ d12 dt

Q: t 3. An infinite sheet lying in the z = 0 plane carries a surface current of density Js = -0.2 cos(6…

A: This is a problem of electromagnetism. The detailed solution is given in the next step.

Q: Q4) Find the Norton equivalent circuit for the portions of the networks of Fig. 4 external to branch…

A: The given circuit is shown below Find Northern equivalent circuit and power dissipated through 100…

Q: A 3 Bus network is shown. Consider generators as ideal voltage sources. If rows 1, 2 and 3 of the…

A: Solution !!

Q: Question-9 The positive, Negative and Zeroes sequence per unit impedance of two generators connected…

A: Given- Impedance- X1=0.12 p.u.X2=0.096 p.u.X3=0.036 p.u. Voltage E=1 p.u. To Find- The positive…

Q: Find the impulse response h [ n ] of the causal LTI discrete-time systems satisfying the following…

Q: E 120 Vrms 60 Hz 0° R1 ww 10Ω L1 mm. 150m H O A D R5 5002 L 250m H R3 2502 C1 :30μF

Q: 12). A motor in a building system has rated power input of 4200 W with power factor of 0.65 and an…

A: Power input to motor =3×line voltage×line current ×power factor. Efficiency =output powerinput…

Q: Q5) Find the Thevenin equivalent circuit for the network in Fig. 5. Then, under the maximum power…

Q: If R1= 1 Ohm R2= 2 Ohm. Suppose R1 and R2 are connected SERIES. Then what is Equivalent (a)10 Ohms…

A: Given data, Resistances are given as, R1=1 Ω, R2=2 Ω

Q: The motor provides torque, which rotates the robot arm with mass 1) Derive Transfer function for the…

A: The given diagram is shown below. We need to determine the transfer function of the motor and…

Q: Find the amplitude and frequency of the following waves: 2.1. 15 sin 377t

Q: A 4 bit module 16 ripple counter uses JK flip-flop. If the propagation delay of each flip flop is…

Q: An 8085 assembly language program is given below. Line 1: MVI A, B5H 2: MVI B, OEH 3: XRI 69H 4: ADD…

A: Given Assembly language program. We have to find the content of accumulator after the execution of…

Q: Vin 1 uF 80 k Ohm 80k 20k 20 k Ohm 3k 3 k 0hm 1 k Ohm Vo 5 kOhm V

Q: If the output of a transistor amplifier is 5 V rms and the input is 100 mV rms the voltage gain is O…

Q: 2. Compute the kinetic energy of an 1800 lb automobile traveling at 30 mi/hr, How many times as…

A: We need to tell about kinetic energy .

Q: Explain why measuring the voltage or current in a circuit can never be exact.

A: Current: It is the time rate of the change of the charges. It is also known as the flow of the…

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

2- A 208 V, 60 Hz, 4 pole, three phase induction motor has a full load speed of 1755 r.p.m.
Calculate its synchronous speed, the slip and rotor frequency

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If a 4-pole induction motor has a synchro- nous speed of 1500 r.p.m., then, supply fre- quency is (1) 50 Hz 60 Hz (iii) (ii) 25 Hz (iv) none of the above
8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical power developed by the motor is ............ (i) 20 W (iii) 500 W (ii) 980 W (iv) 200 W
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
Why do we need to have brushes in a squirrel-cage rotor type induction motor? (short answer)
1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
The frequency of rotor current in a 6-pole, 50 Hz, 3-phase induction motor running at 950 r.p.m. is (1) 2.5 Hz (iii) 5 Hz (ii) 1.5 Hz (iv) 0.05 Hz
The rotor of a 3-phase, 60 Hz, 4-pole induction motor takes 118 kW at 3Hz. The motor has stator copped loss of 2.95 kW, a mechanical loss of 2kW and a stator core loss of 1.7 kW. Solve for the motor efficiency
The rotor of a 3-phase, 60-Hz, 4-pole induction motor gets a total of 120kW through the air gap with a rotor frequency of 3Hz. a. What is the rotor speed (RPM)? b. What is the rotor copper loss (W)?
Q3 A 50 Hz split-phase induction motor has a resistance of 50 and an inductive reactance of 200 in the main winding as well as starting winding. Determine the value of resistance and capacitance to be added in series with the starting winding to send the same current in each winding with a phase difference of 90°. Ans[ 14.99 Ω, 127.5μF]
3.8 An induction motor having 8 poles runs at 727.5 rpm. If the supply frequency is 50 Hz, the emf in the rotor will have a frequency of (a) 1.5 Hz (b) 48.5 Hz (c) 51.5 Hz (d) 75 Hz
A 18600 W induction motor with six poles operates at 60Hz and shows a full-load slip of 6%: i) What is the synchronous speed of the motor? ii) Determine the rotor speed and the slip frequency.
(6) The air gap power of 440 V, 50 HZ 6 pole 3- phase induction motor is 100 KW. The rotor frequency is 1.3 HZ. Find rotor copper losses per phase.