1980 4090 1572 408 720 1636

Q: Question 3 When rounded off to the nearest hundredth, 36. 24445 becomes A. 36.24 B. 36.3 C. 36.2 D.…

A: A multiple choice questions has been given and it has been asked to determine correct option. Please…

Q: Which of the following corresponds to the value of Ry?   Select one: a. 14.20 b. 16.10 c. 14.64 d.…

A:

Q: vernier and micrometer

A: Dimension measurement = main scale reading + ( thimble scale reading × least count) Main scale…

Q: diameter 35 Cm- -> Ain 30cm th=30) (water> high Cm 30cm 5cm aiameter)

A:

Q: 2. Arrange the following measurements in descending order:

A:

Q: Lloukle Inte gr ation Meth od Lletermine the ff :). LDefle etion at e). Mope at C

A:

Q: Find the Inertia about the centroidal axis parallel to x-axis and y-axis

A: To Find the Inertia about the centroidal axis parallel to x-axis and y-axis

Q: Please help me plot a graph using the data provided it must look similar to the second picture

A: helping to understand graph Q(gpm) Q(cfs) Hp(ft) 0 0 120 2000 4.44 125.36 3000 6.66 132…

Q: y 0₁ Variable FR 02 F2 F3 5 13 0₁ = 12 0₂ F3 F₁ Values for the figure are given in the following…

A:

Q: 2. Compute for the moment of inertia about xo and yo of the following figures. a) b) 100 mm 100 mm…

A:

Q: 1. Locate the geometric centroid of the along the x and y axis of the figure shown below. 250.0000…

A: Due to summery about y axis it is clear that centroid of y axis will be at half the distance from…

Q: Soo > 100 - Azz SOo X (0030 AT = Soom Tioom Soum 100m Ioom 100m 200 M

A:

Q: What are the values of X, and Y of the table below using the storage-indication method and equation…

A:

Q: If the collar at A is fixed to the member and can slide vertically along the vertical shaft which…

A: Hi there! you haven't mentioned your ID so, I have taken the values of A and Y from the given…

Q: Critical duration ? P2 16 days 18 days 15 days 17 days 3 R 4 3 5 U 3 W 2 2

A: A network has been shown in the above figure. We have to find out the critical duration of the given…

Q: Calculate the coordinates of a foresight point P101 using the following data: Occupied point O: N…

A: Point O BS=0.45 m HI=144 m FS=- Elevation=143.55 m Azimuth=285 degree Distance=35.3 m Point A BS=-…

Q: QUESTION 11 The second moment of area about the neutral axis of the H-section shown in the figure…

A: Solution Divide the section into three-part

Q: 1. Locate the geometric centroid of the along the x and y axis of the figure shown below, 250.0000…

A:

Q: -100 80 A3 200 1. What is the value of ybar from the 1-1 line ( Select] 2. What is the value of…

A:

Q: 1) choices: 49.81 62.59 59.62 52.69 2) choices: 42315487 mm^4 34643447 mm^4 31534337 mm^4 31943887…

A:

Q: y 50 mm x' 30° 450 mm 350 mm 50 mm 50 mm 300 mm

A:

Q: Briefly discuss the characteristics of Figure 7.4 in May’s textbook.

A: Given data- A contour map from Santa Monica Freeway Surveillance system given. To Find- The…

Q: Critical duration ? P ם 2 16 days 18 days O 15 days O 17 days > 3 R 4 S S3 5 U 3 W 3 2 2

A:

Q: A car and truck front views are shown in the following figure. All unit shown are in milli meter.…

A:

Q: Critical duration ? 22 O 16 days 18 days 15 days O 17 days ( 3 R 4 53 S 5 U 3 2 NX 2

A: This question is related to the CPM and PERT from Civil Engineering.Find out - Calculate the…

Q: Find Quartile deviation velocity data of vehicles on highway

A: To find Quartile estimate of given velocity data…

Q: Survey Sarvey Targe Average value after CLR zero with multiple rounds Reading Average Valne after…

A: The angular measurement is the process of determining the direction of a line with reference to any…

Q: 2. Locate the centroid of the shaded figure. Show your solutions and tabulate your data. 0.50 2.00…

A: Given: Required : Centroid for shaded figure

Q: Draw the following figure using AutoCAD commands R14 Ø86 R49 30 R18 R7 29 R14 Ø53 Ø38 96 192 192 96

A: Question being asked here is to draw the given figure using the AUTO CAD software. And the following…

Q: If the maximum allowable noise is 134.5 decibel (db), what percent of the data of in the following…

A: Given Data:  Maximum Allowable noise = 134.5 decibel Central Mid Point Frequency 148 2 139 3…

Q: The following is a page of an old level field book, in which some of the missing entries are shown.…

A:

Q: Hello, thank you for the help. Could you please tell me why you divided the velocity by 1000 in the…

A: Given: WT = h1+½ v12 -h2  required: Explain why ½ v1² is divided by 1000.

Q: Determine M, if f, = 420 MPa and f'c = 28 MPa. %3D 75 75 75 75 mm mm mm mm 150 mm 75 mm 75 mm 825 mm…

A:

Q: 500 100 300 Hollow Hollow Hollow 150 50 125 300 75

A: Note: As per bartleby guidelines we are allowed to answer only first question of given multiple…

Q: 20 mm 75 mm 10 mm 37.5 mm 37.5 mm

A:

Q: What is the smallest reading a vernier caliper can have if it has 20 divisions in the vernier scale?…

A: LEAST COUNT OF VERNIER CALLIPERS= VALUE OF SMALLEST DIVISION ON THE MAIN SCALE/NO OF DIVISION ON THE…

Q: Question No. 2: inertia at the neutral axis of the given cross section, as shown in the figure. Find…

A:

Q: How to solve it in calculator, what mode do I use, and how to input it in calculator. Thank you.

A: I give answer in three parts, 1) the concept 2) procedure 3) solution.  If you are in hurry directly…