If the maximum allowable noise is 134.5 decibel (db), what percent of the data of in the following table is above that value?

Q: ст ג'Tיוידי 61 Value: mm Value: cm 1 2 3 4 5 6 7 8 9 10

A: The main scale reading = 5.4mm Coinciding vernier division, (CVD) = 1Least count = 0.01mmThe vernier…

Q: WHAT IS THE HEIGHT OF THE FLAGPOLE IF THE HEIGHT OF THE INSTRUMENT IS 1.38m AND = 32° 45' and AB =…

A:

Q: s this correct? interpolate. Specimen No. Time (second) Penetration (mm) 1. 30 40   180 38   800 34…

A: Initial time corresponding to 25 mm penetration

Q: *The R.L, of the point A which is on the floor is 100 m and backsight reading on A is 2.455 m. If…

A:

Q: Find the missing rainfall (in mm) at station X. (given data are in mm) Rain gauge Normal Actual A…

A:

Q: For the same two-span continuous beam in Problem 1, determine the moment at C if point C settles 1.5…

A: Given that :-The two-span continuous beam has following specifications :I = 300 E = 29000…

Q: 1. Fill in the following form of a horizontal angle measurement with a DJ6 theodolite, and try to…

A:

Q: Discuss the purpose of the pseudorandom noise codes.

A: The Pseudo Random Code  is a fundamental part of GPS. It's just a very complicated digital code, a…

Q: 2000 KN 400 kN/m 200 kN/m mm sn -10 -10 m For the beam loaded as shown, what is the location where…

A: It is asked to determine For the given beam and loading, the location of zero slope from the right…

Q: 1. A sound has a magnitude of 40 dB at 100m from its source. What is the magnitude at 50m from the…

A: As per the company guidelines, we are obliged to answer only one question at once. Therefore, please…

Q: QUESTION 6 To measure the passing sight distance, what is the height (ft) of the object?

A: Answer  :- To measure the passing sight distance height of object is  3.5 ft .  Explanation :-…

Q: 1- Comment on your results. 2- Compare between the practical and theoretical results. 3- When is…

A: No circuit is given in the question, Do i just illustrated the following example. This circuit is…

Q: a) Locate the centroid of the shaded area b) determine the moment of inertia about x axis. c)…

A: Draw the Free Body Diagram of given section:

Q: Compute the maximum bending moment of the given beam below. (kN-m) Note: Use two (2) decimal places…

A:

Q: (a) Locate the centroid andỹ of the shaded area. Given, h (20+ last digit of your ID) cm y 40 cm h

A: Consider the free body diagram; Calculate centroid of area BCD from y-axis x1=23×80x1=1603cm…

Q: The equivalent sound power level (in dB) of the four sources with the noise levels of 60 dB, 69 dB,…

A: given- noise levels-60 dB69 dB70 dB79 dB

Q: (b) The data from a levelling survey are shown in Table Q2. Using the rise and fall method,…

A: reduced level - Height of point from means sea level is called R.L. Benchmark - its is the fixed…

Q: r for a theodolite

A: To design: Vernier for a theodolite circle divided into degrees and half degrees to read upto 30"…

Q: s) Compute Mn. 1.200 m f- 28 MPa 1,= 350 MPa 100 mm 330 mm 500 mm 2 #36 70 mm 250 mm

A: Given data: Wf=1200 mmtf=100 mmWw=250 mmDf=400 mmf'c=28 MPafy=350 MPa

Q: If an EDM instrument has a stated accuracy of +-(2mm+3ppm) what error can be expected in a measured…

A: Given data in question  EMD instrument Accuracy Distance To find out  Error

Q: A distance between point (A) and (B) is (170m) was measured by a tape of (20m) length, the it was…

A: L=20m

Q: Determine the y-coordinate (y-bar) of the centroid of the shaded area. (Use 3 decimal places) P=136…

A:

Q: BEGO AV 6 MM CM X 2 2 5 24 INCH Styles Title 1 No Spac..... Question 2: Given that this soccer field…

A: Given Goal to goal distance = 100 m Required  Representative factor,RF of image

Q: Situation C. Using the figure, supply the data needed in the numbered cell. BS 1.27 FS 4.91 BS FS…

A:

Q: Determine the area moment of inertia about the xo- and yo-axes, which pass through the centroid of…

A:

Q: Determine the y-coordinate of the centroid of the shaded

A:

Q: Tail 3m 1+1 18 M/ GIZ Во qm M2 W G& BF BF Xx 18m 11,000 kg Tim 1.8m

A:

Q: tomm lo tromm Samm Ix = 1.04 * 10^6 Ix = 2.01 * 10^6 Ix = 1.01 * 10^6 Ix = 1.8 * 10^6

A:

Q: Question 8 (1) Question 9 (1) What is the FS Reading What is the BS reading ? Answer: Answer: 4 2

A:

Q: 3.24 Refer to the 15-ft high embankment shown in Figure 3.8. Embankments are generally constructed…

A: Given information:

Q: What is the range of the filtering velocity in baghouses?

A:

Q: Pls draw a SFD and BMD for the following picture.

A:

Q: DEFLECTIONS IN BEAMS USING MOMENT AREA METHOD: Given the beam, determine the following: For simply…

A:

Q: Staff reading taken on a benchmark or a point of known elevation is called A. Any one of these B.…

A: Staff reading taken on a benchmark or a point of known elevation is called Back Sight reading.…

Q: Situation D. Using the figure, supply the data needed in the numbered cell. BS FS 3.06 BS FS BS FS…

A: Given data in question  Back sights Fore sights Elevation of BM To find out  Complete the table.

Finishing Operations

Finishing operations are the processes that are applied to the workpiece at the end of a manufacturing process, and after completing all other relevant operations that bring the product to its required dimensions. Finishing operations involve polishing, reducing the surface roughness, eliminating wrinkling, and grinding to enhance the surface texture and provide a better surface finish to the workpiece surface.