19. knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the diameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the corresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in each support bracket at C. 75 mm 9 mm - 300 mm- B 125 mm D 5 mm

19. knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the diameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the corresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in each support bracket at C. 75 mm 9 mm - 300 mm- B 125 mm D 5 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A chain block is hanged on a pin which is supported by plates on both side as shown. If the maximum safe load capacity is 3000 lb, determine (a) the shearing stress on the shaft having a diameter of 1.75 in. (b) and the thickness of the plates if the bearing stress on the plates is 20% greater than the shearing stress.
The compressed-air tank AB has a 250-mm outside diameter and an 8-mm wall thickness. It is fitted with a collar by which a 40-kN force P is applied at B in the horizontal direction. Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum normal stress and the maximum shearing stress at point K. (Round the final answers to one decimal place.)
Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness of the element is 0.8 in., determine the combined normal stresses at points (a) and (f). 1.5 in. 1.5 in. B a ob С 8 in. □e 0 f 8 in. 6 kips 35° 8 in.
Question 3. A 4 by 4-in. wood-post BC is connected to a 1-in. diameter steel eye-bar AB to form a hoist. A load of w = 7000 Ibs is applied at point B on the hoist. (a)Determine the axial stresses in members AB and BC. (b) Determine the cross shearing stress in the 1-in. diameter bolt at point A. STEEL V -7000 lb WOOD FIG. I A
19. knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the diameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the corresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in each support bracket at C. 75 mm 9 mm 300 mm PI 125 mm D 5 mm
w=15
SECTION B(1) Question 1 The bell crank CBA is connected to a pin support B in double shear with 8-mm diameter pin B and to the 10-mm diameter rod CD. Knowing that the ultimate shearing stress is 110 MPa for the steel used in pin B and the ultimate normal stress is 230 MPa for the steel used in rod CD. Determine the maximum vertical force P that can be applied if an overall factor of safety of 1.5 is desired. 45% 300 mm B Figure 1 -450 mm-
PROBLEM 7.26 0.2 m The axle of an automobile is acted upon by the forces and couple shown. Knowing that the diameter of the solid axle is 32 mm, determine (a) the principal planes and principal stresses at point H located on top of the axle, (b) the maximum shearing stress at the same point. 3 kN 350 N- m 3 kN Omax = 18.67 MPa = -158,5 MPa O min
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a xin. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.75 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 16 IN 8 in 16. ---4 in- The largest load P that can be applied at Dis[ lb.
A spherical gas container having an outer diameter of 5 m and a wall thickness of 22 mm is made of a steel for which E=200 GPa and v =0.29. Knowing that the gage pressure in the container is increased from zero to 1.7 MPa, determine (a) the maximum normal stress in the container, (b) the increase in the diameter of the container
PROBLEM 1.2 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d = 50 mm and dz = 30 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC. 300 mm 40 kN 250 mm V30 KN
A 5.49-m-long steel rod must not stretch more than 2.45 mm and the normal stress must not exceed 189 MPa when the rod is subjected to a 9.92-kNaxial load. Knowing that E = 198.5 GPa, determine the required radius of the rod in mm. Express your answer in four decimal places. Add vour answer