19. AT-section of a beam, as shown in Fig. 5.44, is subjected to a vertical shear force of 100 kN. Calcu- late the shear stress at the neutral axis and at the junction of the web and the flange. The moment of inertia at the neutral axis is 113.4 x 10° mm. [Ans. 11.64 MPa; 11 MPa; 2.76 MPa] - 200 - - 60 Flange 50 15 15 120 250 Web 150 15 E 60 All dimensions in mm. All dimensions in mm.

19. AT-section of a beam, as shown in Fig. 5.44, is subjected to a vertical shear force of 100 kN. Calcu- late the shear stress at the neutral axis and at the junction of the web and the flange. The moment of inertia at the neutral axis is 113.4 x 10° mm. [Ans. 11.64 MPa; 11 MPa; 2.76 MPa] - 200 - - 60 Flange 50 15 15 120 250 Web 150 15 E 60 All dimensions in mm. All dimensions in mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QB4 BENDING STRESS The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure QB4). Determine: a) The position of the horizontal neutral axis. b) The second moment of area of the section about the horizontal neutral axis. c) The values of the maximum tensile stress and the maximum compressive stress in the beam if it supports a maximum bending moment of 1200x10 N.mm and the base face is in tension. 150mm 50mm 250mm +50mm I 50mm 150mm Fig QB4
If the beam is subjected to an internal moment of M = 30 kN-m determine the compressive bending stress in MPa on the top surface of top flange A. 50 mm 50 mm 10 mm M 150 mm 15 mm
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the internal shears force is maximum. (tı=15 mm, t2=20 mm, h=150 mm, b=50 mm) 。王! 20 kN/m A |-b-| to 2 m 2 m - 2 m
3 The rigid bar EFG is supported by the truss system shown. Determine the cross- sectional area of member AE for which the normal stress in the member is 105 MPa. 0.90 SONRAWING D B R 15 kN -1.2 m 1.2 m-1.2 m-
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
500 MPa 0.006 120 kN 100 mm - 20 mm 120 kN The tensile load is now removed, and the ends are now subject to a shear force of 10 KN in the same plane as the cross-section (i.e., the force is acting "horizontally"). Assume elastic behavior. d) Determine the shear strain resulting from this shear force (ignoring any bending effects) e) What is the horizontal displacement of one end of the rod relative to the other end under this shear force?
P, 25 mm 60 mm P, 2 m 1m- 1m- For the beam and loading shown, consider the cross section nn. (a) Bending moment in section nn M| its absolute value in Nm units, (b) the absolute value of the normal stress in the x-axis direction at point A of the section nn lox The absolute value of the maximum shear stress at point A of cross section (c) nn , in MPa units |Tmax| Specify in MPa units. The inside of the beam is filled and the section dimensions are as in the figure. Bearings only support vertical forces. Take the value of P 1 in the question as 188 N and the value of P 2 as 381 N. Point A is at the bottom of the beam.
In the given cross section, the neutral axis relative to the bottom fiber is 63 mm and the moment of inertia with respect to the neutral axis is 30,950 mm4. Shear force is 13 kN and bending moment is -120 N-m. Determine the: -Maximum flexural and shear stress in the cross-section (MPa) 65 mm 33 100 mm 46 mm 50 mm 25 mm ↑
Problem 3-31 P + (ks) given: The lap joint is connected together using a 1.25-in.-diameter bolt. the bolt is made from a material having a shear stress-strain diagram that is approximated as shown, P 75 61.1_ 0.05 y (rad) Required: Determine the permanent shear strain in the shear plane of the bolt when an applied force of P = 150 kip is removed.
A For the given loaded beam shown and its cross section: 25 kN m B m Im C 10 kN/m 3 m 2 m- E -120- Determine: -10- (a) The maximum tensile bending stress in the beam. (b) The maximum compressive bending stress in the beam. (c) The maximum shear stress in the beam. 10 150
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m