1800 N/m -2 m- 400 mm 300 'mm Prob. 8–46

Q: Determine the angle of twist at the free end A of the shaft

A:

Q: The truss pinned to the floor at D, and supported by a roller at point A is loaded as shown in the…

A:

Q: A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer…

A:

Q: The 550-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: Given Esteel=200 Gpa  a= 1 m, b= 1.5 m, d= 40 mm, h= 10 mm

Q: 155 kN 125 kN B D F 3 m H C E G 4 m 4 m 4 m 4 m A,

A:

Q: Determine the moment M in kN-m that must be applied to the beam to create maximum stress of 97 MPa.…

A:

Q: The motor A delivers 3000 hp to the shaft at 1500 revimin, of which 1000 hp is removed by gear B and…

A:

Q: *8-52. Beam AB has a negligible mass and thickness, and supports the 200-kg uniform block. It is…

A:

Q: Consider the  hollow steel  square tube  placed on the simply supported over hanging beam. the tube…

A: Given Data: Size of the tube is b=25 mm. Thickness of the tube is t=0.5 mm. Length of the tube is…

Q: The rigid bar AC is supported by a hinge at A and a steel cable BD having a diameter of 12 mm. The…

A: Take moment about A:∑ MA=0F5-FDB3=0FDB=14,4kN

Q: There is a P = 188 KN load applied in the mid-span of the below simply supported beam with the given…

A:

Q: 100-lb.homogeneous plate is supported by a ball joint at A, a simple bearing at B, and a cable at C.…

A: Given:- W=100lb Vertical  force=120lb To find:- Force

Q: Q5. The system shown consists of three bars having different flexural rigidities with El2 = 2El, and…

A: Given: Flexural Rigidity EI2 is equal to twice of Flexural Rigidity EI1 i.e EI2=2EI1

Q: 1. From the given continuous beam with the corresponding loads as shown and using slope deflection…

A:

Q: A rectangular concrete beam has a width of 300 mm and an effective depth to bottom bars of 450 mm.…

A:

Q: A tubular post of outer diameter d₂ is guyed by two cables fitted with turnbuckles (see figure).…

A:

Q: 2. Determine the reactions at supports A and B. 700 Ib/ft 500 Ib/ft 6 ft 9 ft 6 ft 6 ft 8 ft

A: Consider the following free body diagram: Consider member BD as follows:

Q: 3- The beam - column below, which has two ends and Concentrated load Q-80 KN and compressive load…

A: Note : Since there are two questions given in a single question window. As per guidelines only 1st…

Q: The frame below is made up of three 2 m long rods. The pin at D resides in a slot with a friction…

A: Given : Length of rods = 2m  Friction coefficient = 0.35  Determine if the frame slips when a 10 N…

Q: H.W Replace the loading equivalent resultant force and specify its location on the beam, measured…

A: Consider the given beam. The resultant force will be equal to the algebraic sum of all the forces.

Q: Determine the force in member CG for the truss using the method of joints. 133 kN 67 kN B F G -4 at…

A: Given Data  Find the force in member CG (FCG) using method of joint.

Q: A rectangular concrete beam has a width of 300 mm and an effective depth to bottom bars of 430 mm.…

A:

Q: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of…

A: Given:- The two forces are applied to the end of the boom OA The magnitude of one force = 200 lb The…

Q: Determine the resultant force at pins A, B, and C on the three-member frame. P=129 N q=200 N/m

A: Load P = 129 NLoad intensity q = 200 N/m

Q: The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the…

A:

Q: A cantiliver beam subjected to a uniform load along its length and axial load P. Draw the shear and…

A: Determine maximum shear force and maximum shear stress

Q: 1. Compute the force in member FEF 2. Compute the force in member FED

A:

Q: A reinforced rectangular beam with width b and effective depth d has 4 16 mm bars placed on 1 layer…

A:

Q: в с D E F G Hinge Hinge 4 m- - 4 m+3 m--3 m- 2 m 2 m a) Determine the maximum positive moment that…

A:

Q: What is the Maximum moment in kN-m. Given: W = 20, a = 2, b = 8, and P = 70. %3D PkN am W KN m b m R

A:

Q: IG =1.35 kg m coefficients of friction between the spool and the ground are 0.30 and 0.27,…

A: a.) Draw the free body diagram

Q: The beam is subjected to an internal moment of M = 140 kN.m. Determine the bending stress developed…

A:

Q: A 1.5 m 1.5 m 1 m + 0.75 m В с S

A:

Q: Three pulleys are joined by solid steel shafts AB and BC. If G = 200 GPa, determine the unit…

A:

Q: 1200 kN 300 mm 300 mm

A:

Q: a negligible mass m block. It is pinne of 20 kg and negli static friction at B-

A:

Q: 3. The shear stress is limited to 60 MPa. Consider G = 84,000 MPa. a. Determine the diameter of a…

A: Using formula

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.