Untitled PaintFile View69XClipboard▷ 1224, 491pxQ Searchd23ImageNV607 x 634px18°D10 A4ToolsⒸd₂d₁PROB. 2.5-8El168 CHAPTER 2 Axially Loaded Members2.5-8 A brass sleeve S is fitted over a steel bolt B (seefigure), and the nut is tightened until it is just snug. The bolthas a diameter d = 25 mm, and the sleeve has inside andoutside diameters d₁ = 26 mm and d₂ = 36 mm, respec-tively.dвBrushesCalculate the temperature rise AT that is required toproduce a compressive stress of 25 MPa in the sleeve.(Use material properties as follows: for the sleeve, as =21 X 10 °C and Es= 100 GPa; for the bolt, ag = 10 X106/C and EB 200 GPa.) (Suggestion: Use the resultsof Example 2-8.)1920 x 1080pxN40Sleeve (S)ShapesBolt (B)4+MSizeOOO00000Colors100%AVENGI00% X+11:33 CH30/11/2022

To determine: The temperature rise that is required to produce a compressive stress of 25 MPa in…

168 CHAPTER 2 Axially Loaded Members 2.5-8 A brass sleeve S is fitted over a steel bolt B (see figure), and the nut is tightened until it is just snug. The bolt has a diameter dg = 25 mm, and the sleeve has inside and outside diameters d₁= 26 mm and d₂ = 36 mm, respec- tively. Calculate the temperature rise AT that is required to produce a compressive stress of 25 MPa in the sleeve. (Use material properties as follows: for the sleeve, as = 21 X 10 C and Es= 100 GPa; for the bolt, og = 10 X 10-6/C and Eg= 200 GPa.) (Suggestion: Use the results of Example 2-8.)

168 CHAPTER 2 Axially Loaded Members 2.5-8 A brass sleeve S is fitted over a steel bolt B (see figure), and the nut is tightened until it is just snug. The bolt has a diameter dg = 25 mm, and the sleeve has inside and outside diameters d₁= 26 mm and d₂ = 36 mm, respec- tively. Calculate the temperature rise AT that is required to produce a compressive stress of 25 MPa in the sleeve. (Use material properties as follows: for the sleeve, as = 21 X 10 C and Es= 100 GPa; for the bolt, og = 10 X 10-6/C and Eg= 200 GPa.) (Suggestion: Use the results of Example 2-8.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70 electrodes. The width of the plate is 50 mm and the thickness is 12 mm. Use Fy = 248 MPa T+ T4 O 29 mm O 30 mm 1. Which of the following nearly gives the diameter of the slot weld using the LRFD method. O 27 mm E70 O 28 mm T T
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
PLEASE ANSWER ASAP
Q.2. The rigid bar AB, atrached to two verti cal rods as shown in Fig (e), is horizontal before the lead p is applied. If the load pe so kN, ditermine its Vertical mmovement. Aluminum Steel A300 mm 200 G A500 mm R-70 GN -3m- Fig (2)
Q3-1 (Trusses), For the Figure shown below; 1 1. Find the forces in the members AB and AD of the truss and indicate whether it is in tension or 3m compression. 10KN 2. Read the following paragraph carefully then answer if it's TRUE or FALSE: The force in the member BC equal to zero? 3. Read the following paragraph carefully then CHOOSE THE CORRECT English Fried Safe 10KN 15 AN 3m 20 kN
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear