16.Determine the number of degrees of freedom at the plait point below. Ternary (3 – Component) Phase Diagrams 2- phase regions in ternary systems are determined through experimental data. The lever rule still applies to 2- phase regions. However, there are points that should be identified before constructing a tie line: B The plait point: the point in the binodal curve (boundary of the 2- phase region) in which the composition of the 2 separate phases are equal. Plait Point Tie Lines The tie lines are constructed through experimental data. These tie lines can be extended outside the bounds of the diagram to determine the delta point. Any straight line that can be drawn from the delta point that passes through the binodal curve at 2 points can be used to perform the Lever Rule. The Plait Point is the tangent line of the binodal curve that passes through the Delta Point. Delta Point C

16.Determine the number of degrees of freedom at the plait point below. Ternary (3 – Component) Phase Diagrams 2- phase regions in ternary systems are determined through experimental data. The lever rule still applies to 2- phase regions. However, there are points that should be identified before constructing a tie line: B The plait point: the point in the binodal curve (boundary of the 2- phase region) in which the composition of the 2 separate phases are equal. Plait Point Tie Lines The tie lines are constructed through experimental data. These tie lines can be extended outside the bounds of the diagram to determine the delta point. Any straight line that can be drawn from the delta point that passes through the binodal curve at 2 points can be used to perform the Lever Rule. The Plait Point is the tangent line of the binodal curve that passes through the Delta Point. Delta Point C

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

1. It is the lowest temperature at which a liquid is present in a solid-liquid system. 2. It is the point where the concentrations of both equilibrium phases in a liquid-liquid system are equal. 3. What do you call the state at which the compositions of the vapor and liquid are equal? 4. In a vapor liquid system, at what point will the mixture becomes a saturated vapor? Choices Dew point critical point triple point bubble point azeotrope eutectic point immisibility supercritical fluid plait point
Find the total vapour pressure of an ideal binary mixture of two liquids, A and B. The vapour pressures of A and B are 75 Torr and 25 Torr respectively at 25 °C. The mole fraction of A is 0.75 in the vapour that is in equilibrium with the solution. O A. 62.5 Torr O B. 50 Torr O C.100 Torr O D. 30 Torr O E. Data Insufficient Rationale
1. The carbon radical intermediate that formed from ibuprofen in this experiment is shown below. Draw all resonance structures of the radical intermediate (show electron-pushing arrows). for HO
It is desired to prepare a new drug "Y" for which various degrees of the dissolution of the product in water is prepared to measure the effectiveness of the drug in various dosages and it is also desired to determine the relationship between the entropy changes of the samples in the face of various situations. . One of the solutions to be studied contains 100 grams of water and 5 grams of "Y" and the melting point measurements indicate that the solution is 0.54 molal. From this prepared solution, a 50 gram sample is taken at 0 ° C and solidified in a freezer that is at a temperature of -18 ° C. Data: ΔH fus of the studied solution = 0.33 KJ / gr. Molecular Weight of Y = 150 -Calculate the degree of dissociation for the sample that is being studied.
1. A hypothetical three component system has a composition of 24% A, 40% B and 36% C. Plot this composition in a Roozeboom diagram.
Solid-liquid phase diagram of naphthalene-biphenyl system was formed by determination of arrest and break points in cooling curves of different composition mixtures as follows 82 283 2222 90 80 Temperature (°C) 111 70 1 50 40 30 20 10 0 Area Area 1 0.2 Phase Diagram Area Il Area IV Area III 0.8 0.4 0.6 Mole fraction of naphthalene 1 a. Write the phases of naphthalene and biphenyl in different areas on graph (assume that these molecules are completely miscible in liquid phase and immiscible in solid phase) of phases Explanations (Which phases present?) 12 b. Explain briefly the eutectic point and explain its position on graph
When carrying out a freezing point depression experiment, what will be the effect on a calculated molar mass of an unknown substance if supercooling was observed to occur during the freezing point measurement for the unknown substance?
Describe the changes you will observe by increasing the temperature of the triethylamine / water mixture in point a in the drawing below to point a ''. How the relative number of separate phases changes triethylamine and water along this path? How do you calculate the relative amount of separate phases of triethylamine and water at point a ’’? Explain exactly how the calculation is done. Please make the solution as simple and understandable as possible.
Identify the number of degrees of freedom and potential intensive variables for a mixture of benzene and toluene in equilibrium with the vapor phase.
At –10.5 °C, a common temperature for household freezers, what is the maximum mass of aspartame (C14H18N2O5) you can add to 3.00 kg of pure water and still have the solution freeze? Assume that aspartame is a molecular solid and does not ionize when it dissolves in water. Consult the table of KĘ values. mass of aspartame: g
3. Determine the number of components, phases and the degrees of freedom in the following systems: (i) (ii) (iii) (iv) An aqueous solution of sugar Br2(1) dissolved in CC14(1) A mixture of N2(g), H2(g) and NH3(g) Fe(s) + H₂O(g) FeO (s) + H2(g)
Explain why the boiling point of a two-component mixture rises slowly throughout a simple distillation when the boiling-point differences are not large.