16.11 An 8-lb uniform slender rod AB is held in position by two ropes and the link CA which has a negligible weight. After rope BD is cut the assembly rotates in a vertical plane under the combined effect of gravity and 4 lb-ft couple M applied to link CA as shown. Determine, immediately after rope BD has been cut, (a) the acceleration of rod AB, (b) the tension in rope EB. 13A Fig. P16.11 and P16.12 AB D

16.11 An 8-lb uniform slender rod AB is held in position by two ropes and the link CA which has a negligible weight. After rope BD is cut the assembly rotates in a vertical plane under the combined effect of gravity and 4 lb-ft couple M applied to link CA as shown. Determine, immediately after rope BD has been cut, (a) the acceleration of rod AB, (b) the tension in rope EB. 13A Fig. P16.11 and P16.12 AB D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. AS-kg uniform disk is attached to the 3-kg uniform rod BC by means of a frictionless pin AB. An elastic cord is wound around the edge of the disk and is attached to a ring at E. Both ring E and rod BC can rotate freely about the vertical shaft. Knowing that the system is released from rest when the tension in the elastic cord is 15 N, determine (a) the angular acceleration of the disk, (b) the acceleration of the center of the disk. 150 mim C E B 75 mmA D
A uniform rod of length L and mass m is supported as shown. If the cable attached at end B suddenly breaks, determine (a) the acceleration of end B, (b) the reaction at the pin support.
Two identical 4-lb slender rods AB and BC are connected by a pin at B and by the cord AC. The assembly rotates in a vertical plane under the combined effect of gravity and a 6-lb·ft couple M applied to rod AB. Knowing that in the position shown the angular velocity of the assembly is zero, determine (a) the angular acceleration of the assembly, (b) the tension in cord AC.
A 9-kg uniform disk is attached to the 5-kg slender rod AB by means of frictionless pins at B and C. The assembly rotates in a vertical plane under the combined effect of gravity and of a couple M that is applied to rod AB. Knowing that at the instant shown the assembly has an angular velocity of 6 rad/s and an angular acceleration of 25 rad/s2 , both counterclockwise, determine (a) the couple M, (b) the force exerted by pin C on member AB
Problem #5) A pulley having a moment of inertia of 0.191b-ft-s² is connected to two masses as shown. The masses A and B have linear acceleration of 1.85ft/s² upward and 1.11 ft/s² downward, respectively. Assuming no axle friction, determine (a) the tension forces TA and TB in the cables connecting the masses, and (b) the angular acceleration a of the pulley. 6 in. Include and present the Free Body Diagram and Inertial Response Diagram as part of the solving process. Hint #1: Hint #2: use mA = 0.1553slugs, and mB = 0.3106slugs treat each body separately B 10 lb 10 in. A 5 lb
16.8 A load of lumber weighing W = 25 kN is being raised by a crane. The weight of the boom ABC is 3 kN and the combined weight of the truck and driver is 50 kN as shown. Determine the maximum vertical acceleration of the lumber so that the crane does not tip over. A W 2.0 m- 2.0 m- Fig. P16.8 0.6 m 0.4 m ty B 3 kN F H 0.9 m C D 0.3 m -E 50 kN 2.0 m- K k 0.5 m
The steel roll shown has a mass of 1200 kg, has a centroidal radius of gyration of 150 mm, and is lifted by two cables looped around its shaft. Knowing that at the instant shown the acceleration of the roll is 150 mm/s2 downward and that for each cable TA = 3000 N, determine (a) the corresponding tension TB, (b) the angular acceleration of the roll.
A uniform semicircular plate with a mass of 6 kg is suspended from three vertical wires at points A, B, and C, and a force P with a magnitude of 5 N is applied to point B. Immediately after P is applied, determine the acceleration of (a) the mass center of the plate, (b) point C.
Gear A weighs 1 lb and has a radius of gyration of 1.3 in.; gear B weighs 6 lb and has a radius of gyration of 3 in.; gear C weighs 9 lb and has a radius of gyration of 4.3 in. Knowing a couple M of constant magnitude of 40 lb-in. is applied to gear A, determine (a) the angular acceleration of gear C, (b) the tangential force that gear B exerts on gear C. M A 2 in. 2 in. borg J 4 in. B 6 in. с w ណ
Two disks of the same material are attached to a shaft as shown. Disk A has a radius r and a thickness 2b, while disk B has a radius nr and a thickness 2b. A couple M with a constant magnitude is applied when the system is at rest and is removed after the system has executed two revolutions. Determine the value of n that results in the largest final speed for a point on the rim of disk B.
4. (20 pts) A concrete block is lifted by a hoisting mechanism in which the cables are securely wrapped around their respective drums. The drums are fastened together and rotate as a single unit at their center of mass O. Combined mass of drum is 150 kg, and radius of gyration at O is 450 mm. A constant tension of 1.8 kN is maintained in the cable by the power unit at A. Determine the vertical acceleration of the block and the resultant force on the bearing at O. 600 mm 300 mm P = 1.8 kN m = 150 kg ko = 450 mm %3D 45° 300 kg
16.79 A uniform rod of length L. and mass m is supported as shown. If the cable attached at B suddenly breaks, determine (a) the acceleration of end B. (b) the reaction at the pin support. Fig. P16.79 B