150 mm | 150 mm 2 m 2 m σ(MPa) ² = 5(10°)e e(mm/mm)

Q: 14- The anchor shackle supports a cable force of 5.0 kN. If the pin has a diameter of 6 mm,…

A: Given data: The diameter of the pin, d = 6 mm. The applied load, P = 5 kN. Draw the free-body…

Q: A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel…

A: GivenD=4mt=15mmE=200GPaσy=266MPaP=1785 kPa

Q: The rod has a circular cross section. If it is made of an elastic perfectly plastic material where…

A: Elastic stage is a stage where a material under load can regain its original shape after loading is…

Q: Determine the absolute maximum shear strain in 106 unit.

A: The maximum shear strain = 1680 The solution is in next step.

Q: The rigid beam is supported by a pin at C and an A992 steel guy wire AB of length 6 ft. If the wire…

A:

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

A: Stress:  When a component or a part is subjected to any external force, a resisting force will be…

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A: From the curve, write the expression of the elastic modulus of the material. From the curve, write…

Q: 14-22. The bolt has a diameter of 10 mm, and the arm AB has a rectangular cross section that is 12…

A:

Q: The two bars are made of a material that has the stress-strain diagram shown. If the cross-sectional…

A: Given data as per question  Cross-sectional area of AB =1.5 in2  Cross-sectional area of Bc=4 in2

Q: The ball is truncated at its ends and is used to support the bearing load P. The modulus of…

A: Given:

Q: 14-22. The bolt has a diameter of 10 mm, and the arm AB has a rectangular cross section that is 12…

A:

Q: Determine the torsional strain energy in the A992 steel shaft. The shaft has a radius of 50 mm.

A: Free body diagram of shaft . Radius of shaft=50 mm , d=100 mm=0.1 mdivide the shaft into two…

Q: В D 6 kN 5 kN 4 kN A - 2 m→2 m→ -3 m- -3 m

A:

Q: An air-filled rubber ball has a diameter of 6 in. If the air pressure within the ball is increased…

A: Given data :Initial diameter (di) = 6 inFinal diameter (df) = 7 in

Q: Determine the width and thickness of the leaves (in mm) of a leaf spring using the following…

A:

Q: ft, the 6-meter-high arm is manufactured using the l profile given below. It is fixed to both ends…

A:

Q: A leaf spring carries a central load of 3000 N. The leaf spring has to be made of 10 steel plates…

A:

Q: Determine the torsional strain energy in the A992 steel shaft. The shaft has a radius of 40 mm.

A: Draw the side view of the shaft. Let AB be the segment 1, BC be the segment 2, and CD be the…

Q: The distributed loading is applied to the rigid beam, which is supported by the three bars. Each bar…

A: Due to the distributed load the bars will experience equal force. Let the force in each bar be F.…

Q: An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top…

A: Given Data: The horizontal force P = 2 kN. The displacement of the top plate is d = 2 mm. The…

Q: Q1/1) A pipe has an outside diameter of 20 mm, an inside diameter of 10 mm and length 0.30 m and it…

A: Q1) Given data: The compressive force acting on the pipe is F = 50 kN = (50 x 103) NThe outer…

Q: Determine the total axial and bending strain energy in the A992 structural steel W8 * 58 beam.

A: Given, The load on the beam and the free body diagram is shown below.

Q: An elevator with a mass of 500 kg and is supported by a 20 mm diameter cable, 500 m long. When the…

A: Given:me=500 KgWl=7500 Nd=20 mmL=500 mE=200 GPa

Q: The rod is subjected to the linearly varying axial distributed load as shown. What is the correct…

A:

Q: The brake pads for a bicycle tire are made of rubber. If a frictional force of 50 N is applied to…

A:

Q: 11.4 (A/B). Compare the strain energies of two bars of the same material and length and carrying the…

A:

Q: What strain will be produced by a stress of 20 x 10° N/m?, for a given modulus of elasticity 100GPA.…

A: Stress = 20 × 10 6 N/m2 modulus of elasticity = 100 Gpa =100×109N/m² Stress = Strain × modulus of…

Q: Q3 The beam has a rectangular cross section and is made of and elastic-plastic material having a…

A: Stress: The restoring force per unit area of the material  is known as  stress. It is a tensor…

Q: owing that the AB pillar shown below is supported at points A and B, determine the greatest load (w)…

A: Given: To determine the maximum value of w.

Q: The ratio of the strain in the lateral direction to that in the axial direction A Pascal's Number…

A: Given data Strain is the ratio of change in dimension to original dimension.

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

A: Given data: The length of rod, L = 200 mm. The diameter of rod, d = 15 mm. The young’s modulus, E =…

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. 10 ft Part A If the wire…

A: Given data: d=0.5 inw=190 lb/ft Need to determine the stretch in the cable.

Q: 11.3 A load of 20 kg resting on an Inclined plane begins to slip when the plane is tilted to an…

A:

Q: Cable steel has a length of 150 m and stretch to 4 cm when the load is applied at both ends. If the…

A: Given, Initial length = L = 150 m Change in length = ΔL = 4 cm = 0.04 m Stress in the cable = σ = 60…

Q: 7. The point where the stress-strain diagram for structural steel becomes almost horizontal is…

A: The stress -strain diagram for the steel is as follows:

Q: Q01. A weight falls on a plunger fitted in a container filled with oil thereby producing a pressure…

A:

Q: 9.8 A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal…

A: Given data: di=300 mmt=12 mmE=210 GN/m2v=0.3 Need to determine the value of "p" and volumetric…

Q: The slope of the curve in the elastic zone from a specimen subjected to torsion test is: Select one:…

A: Shear modulus is defined as the shear stress induced in a specimen per unit shear strain.

Q: The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: The elastic portion of the tension stress–strain diagram for an aluminum alloy is shown in the…

A: Write the given data with suitable variables: L=2 ind=0.5 inP=10 kip

Q: The strain at point A on the bracket has normal components 750x106 and 150x106 in x and y…

A:

Q: A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical…

A: Density  Density of any substance is defined as the ratio of mass in kg to volume in m3.     Here…

Q: What strain will be produced by a stress of 20 x 10° N/m?, for a given modulus of elasticity 100GPA.…

A: Given :-   Modulus of elasticity, E = 100GPa = 100×109 N/m2                 Stress = 20×106 N/m2  To…

Q: A simple friction stopping device is formed by pressing 2 elastic blocks against a metal spinning…

A: Given data: The contact area between each block and the metal rim is 0.05 m ×0.02 m The thickness…

Q: A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel…

A:

Q: The stress–strain diagram for polyethylene, which is used to sheath coaxial cables, is determined…

A: Given: L=10 in ε=0.024 (in/in) To determine: The approximate length of the specimen, measured…

Q: The stress–strain diagram of the material can be approximated by the two line segments. If a bar…

A: The stiffness of the column material in the elastic region using stress-strain diagram is calculated…

Processing of Polymer Matrix Composites

The polymer matrix composite is described as a composite material that contains some polymer in the form of either fibers or powder. Polymer matrix composites are also known in short as PMC's.