150 mm 100 mm TB T'R 200 mm Tc T'c PROBLEM 4.91 Two transmission belts pass over a double- sheaved pulley that is attached to an axe supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension is 90 N in both portions of belt B and 150 N in both portions of belt C, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust.

150 mm 100 mm TB T'R 200 mm Tc T'c PROBLEM 4.91 Two transmission belts pass over a double- sheaved pulley that is attached to an axe supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension is 90 N in both portions of belt B and 150 N in both portions of belt C, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.24P

See similar textbooks

Similar questions

3 1 kN 4 esc 2 kN Во C 2 kN Do 1 E 180 mm 1 kN F G 2m 2m 2m 2m 2m 2m 160 mm B H C K A 90 mm 0 m 1 m 1m 1m L 1m 240 N 31 PROBLEM 6.131 Arm ABC is connected by pins to a collar at B and to crank CD at C. Neglecting the effect of friction, determine the couple M required to hold the system in equilibrium when 0=0. ▸ % PROBLEM 6.21 L Determine the force in each of the members located to the left of FG for the scissors roof truss shown. State whether each member is in tension or compression. A 6 & 7 * 8 of J O Jul 17 8:13 x
Find the torque on link 2 necessary to maintain static equilibrium for the 4-bar mechanism shown below. Use analytical method, draw free body diagram of each link. O,A = 3.5 in., AB = 0,B = 6 in., O,C = 7 in. P.=50 lb 4 -152. 105 240° M12 2
A circular plate is being supported by 7 outer springs and a central spring. The outer springs are equally placed around a bolt circle. Take note that the outer springs are 2 mm shorter than the central spring. Further, a 5000- Newton force is applied at the center of the plate pushing the springs down.
A 200 m tape weighing 35 N is suspended between the two ends under a standard pull of 176 N. The correct distance between the tape ends is
Pulley A delivers a steady torque of 1100 lb-in. To a pump through its shaft at C. The tension in the lower side of the belt is 165 lb. The driving motor weighs 200 lb and rotates clockwise. Determine the bearing reaction force at O. A 9" B 30° 37 8" 150 lb - 5"-- 5"-
The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V- belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=90ON), coefficient of friction u=0.3 4- the speed of large pulley.
The 4.00 kg block is attached to a vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown in the (Figure 1) and the tension in the upper string is 84.0 N. (A) What is the tension in the lower cord? (Express your answer with the appropriate units.) (B) How many revolutions per minute does the system make? (Express your answer in revolutions per minute.) (C) Find the number of revolutions per minute at which the lower cord just goes slack. (Express your answer in revolutions per minute.)
Q2) In a four-link mechanism shown in Fig. 2, torque T3 =30, T4=30 , 01=0 and force F1=90 The link lengths are AD = 800 mm, AB = 300 mm, BC = 700 mm and CD = 400 mm. For the static equilibrium of the mechanism, determine the required input torque T2.. В T2 (Unknown) 60° T4 (A) 01 f1 Fig 2
L2 L3 D B. L4 L5 L6 Find the magnitude of the force exerted on bolt E, given: P = 85 lbs, L1 = 0.5 in, L2 = 4.5 in, L3 = 1.4 in, L4 = 3.1 in, L5 = 1.4 in, L6 = 1.9 in, L7 = 0.9 in, L8 = 0.2 in Ey = Number Ibs (enter a positive number)
The figure shows a mechanism that raises packages in a transfer mechanism. A 200-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 287 rpm CCW. At the position shown the crank OA is vertical and the output link OB is horizontal. we need to determine the torque required from the motor at the crank O2A and the force in member AB The weights of the links are negligible. 50mm 450mm 200 N 200 mm B. 374 mm 300mm X The angular velocity of the link OĄBD in rad/s is = Choose... + The magnitude of the velocity of point D in m/s is = Choose... + The torque required from the motor at the crank O2A in N.m is = Choose... : The force in member AB in N is = Choose... +
Part A When y is zero, the springs sustain a force of 54 lb . (Figure 1) Determine the magnitude of the applied vertical forces F and -F required to pull point A away from point Ba distance of y = 1.5 ft . The ends of cords CAD and CBD are attached to rings at Cand D. Express your answer to two significant figures and include the appropriate units. Figure 1 of 1 ? F = Value Units Submit Request Answer 2 ft 2ft k = 40 lb/ft www k = 40 lb/ft 2 ft Provide Feedback Next > 6 2 ft O
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. ( Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. ( A = 15°. C A 250 mm eeeeeee 900 mm k= 2.6 kN/m OB = 30° B LC 7-y 200 mm