Please show step by step work 3. Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospaceindustries. Before running machining tests and analyzing machined quality, preliminary efforts are neededto evaluate selected materials and factors affecting machining process¹. Three material candidates havebeen selected, including 422SS (stainless steel), IN718 (nickel alloy), and Ti64 (titanium alloy) with theirmeasured tensile properties and equation of true stress-true strain relationship used listed below. Tref 25°C.Specifically, three factors will need to be evaluated, including different materials, temperature, and sizeeffect. Please calculate true stress values for true strain ranging between 0-3 for each case listed below.MaterialB (MPa)& (S-1)Tm (°C)4000.01422SS (Peyre et al., 2007)IN718 (Kobayashi et al., 2008)Ti64 (Umbrello, 2008)137011E-5Material422SS (CINDAS, 2011)IN718 (Davis, 1997)Ti64 (Fukuhara and Sanpei, 1993)A (MPa)870980782.7G (GPa)498.4-0.04397(°C)+85.709-0.0225 T(°C)+86.003-0.0241 T(°C)+41.097no = (A + B) 1 + c log0.40.1640.28с0.0150.020.028b (nm)0.2480.2490.295T-Tref) (1 + c 108 — 2) (1 - (TTT))Tm-Trefm0.51.031a0.50.50.51/2²)")"X(1 + ((A + B²X1 + c log(2)/(189²2bc² (T- Tud)/(Ta - Trg)))))152013001660μ0.380.380.38(a) At a fixed temperature (T=400 °C) and a strain rate (=105 s-¹, typical for micromachining), please plotand compare the true stress-true strain curves for different materials. A 1 um wide channel will be cut, sothe length parameter, L=10 nm, may be assumed.(b) At a strain rate (=105 s¹) with a fixed length parameter (L=10 nm), please plot and compare the truestress-true strain curves of Ti64 at different temperatures (T-25 °C, 400 °C, 1000 °C).(c) At a fixed temperature (T=400 °C) and a strain rate (¿=105 s¯¹), please plot and compare the true stress-true strain curves of Ti64 if microfluidic channels with different width need to be made, specifically L=10nm, 100 nm, 1000 nm.

Answered: Image /qna-images/answer/2d252b96-4679-452c-8cd2-c87c9a5c133b.jpg

Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace dustries. Before running machining tests and analyzing machined quality, preliminary efforts are needed evaluate selected materials and factors affecting machining process. Three material candidates have een selected, including 422SS (stainless steel), IN718 (nickel alloy), and Ti64 (titanium alloy) with their easured tensile properties and equation of true stress-true strain relationship used listed below. Tref 25°C. pecifically, three factors will need to be evaluated, including different materials, temperature, and size fect. Please calculate true stress values for true strain ranging between 0-3 for each case listed below.

Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace dustries. Before running machining tests and analyzing machined quality, preliminary efforts are needed evaluate selected materials and factors affecting machining process. Three material candidates have een selected, including 422SS (stainless steel), IN718 (nickel alloy), and Ti64 (titanium alloy) with their easured tensile properties and equation of true stress-true strain relationship used listed below. Tref 25°C. pecifically, three factors will need to be evaluated, including different materials, temperature, and size fect. Please calculate true stress values for true strain ranging between 0-3 for each case listed below.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

MIME2204– ENGINEERING MATERIALS
Nondestructive evaluation: Nondestructive evaluation (NDE) describes methodsthat quantitatively characterize materials, tissues, and structures by noninvasivemeans such as X-ray computed tomography, ultrasonics, and acoustic emission.Recently, NDE was used to detect defects in steel castings. (JOM, May 2005.)Assume that the probability that NDE detects a “hit” (i.e., predicts a defect in a steelcasting) when, in fact, a defect exists is .97. (This is often called the probability ofdetection.) Also assume that the probability that NDE detects a “hit” when, in fact,no defect exists is .005. (This is called the probability of a false call.) Past experiencehas shown that a defect occurs once in every 100 steel castings. If NDE detects a“hit” for a particular steel casting, what is the probability that an actual defectexists? Step by Step Full procedure required.
A siilicon boule has been processed through grinding to provide a cylinder whose diameter = 281 mm and whose length = 899 mm. Next, it will be sliced into wafers 0.8 mm thick using a cut-off saw with a kerf = 0.5 mm. The wafer thus produced will be used to fabricate as many IC chips as possible for the personal computer market. Each IC has a market value to the company of $108. Each chip is square with 17 mm on a side. The processable area of each wafer is defined by a diameter = 265 mm. Estimate the value of all of the IC chips that could be produced (in $), asssuming an overall yield of 84% good product.
A plate with a center hole is subjected to both of axial force (F) and bending moment (M; acting about weak axis). Predict the fatigue failure with 50% reliability. The plate is machined from alloy steel (S.= 470 MPa and Sy= 350 MPa). M M [Top View] M M [Side View] Where, w=35mm, d=4mm, h=2mm. 1) Calculate fatigue strength (S,). 2) Calculate o. and o. for two loading cases: (a) F=Fosin (wt-10) and M=0 F=Fosin (t+10) +k and M=Mo and (b) Note: F.= k = 2 kN and M.= 4 Nm 3) Determine if the bar is safe against fatigue failure and calculate safety factor for the cyclic loading cases; assume (a) Obm = 0 MPa and O = 80 MPa and (b) oim = 85 MPa and OE = 70 MPa regardless of the answers in question 2).
1. On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance that is implied between the diameters?
M3 Discuss the importance of standards applied in the engineering environment
. Cite some sources of nonlinearities that arise in the three components of problem formulation. • What are some common ways of dealing with nonlinearities in material behavior or kinematic conditions?
For my assigment, I was asked to design a electric motorbike that has a peformance equal to Honda CBR1000 Fireblade which has a petrol engine. A part of the the assignment is to calculate " An estimate of maximum Power your new motor will need to generate to match the Honda’s performance." I can make the assumption, apart from changing the motor, everything else is going to stay the same so the fairing,the rider and etc they're gonna be the same for the two bikes. So can you please tell me how I can calculate that which information would I need ?
DEPARTMENT OF MECHANICAL ENGINEERINGMENG 303 PRINCIPLES OF COMPUTER AIDED ENGINEERING Failure mode and effect analysis for Autonomous underwater vehicles, based on any standard. plese dont late
The theoretical failure strength is significantly higher than the empirical failure strength of polycrystalline materials, even when they are highly polished because: a) Polycrystalline materials have little or no capacity for plastic deformation, so they have lower failure stresses b) Plastic deformation in polycrystalline materials adsorbs energy which reduces their failure strength c)The energy needed to break the atomic bonds in crystal lattices is lower in polycrystalline materials as compared to in single crystals d)Polycrystalline materials contain internal discontinuities
In your summer internship, you are tasked with measuring the ultimate tensile strength of a material to determine if it meets your company’s (Superior Super Ships Inc) specification. Your boss is worried that the new low-cost supplier, Shoddy Alloys Inc, may not be reliable but it is the only way to source on-time the SS304 needed to make finishings for Jeff Bezos’ new yacht, the Black Pearl. You collect several load versus displacement curves, as illustrated below. The initial diameter of the round gauge section is 0.25 in. You also collect the instantaneous diameter of the specimen during the test using a laser. Using the provided data, calculate what is the ultimate tensile strength measured in this test?
MECHANICAL PROPERTIES OF AGRICULTURAL AND BIOLOGICAL MATERIALS Discuss the following mechanical properties of durable and perishable crops:Grains:a. Elasticityb. Hardnessc. Strengthd. Other properties