14) The motor torque speed characteristic is given by the equation @m = 100 - T where @m is in rad/sec and Tis in N m. The initial motor torque is 10 N · m. A step load torque of 50 N m is applied at t = 0. If the total inertia of the motor load combination is 5 kg · m2, the value of the motor torque after 5 sec is:

14) The motor torque speed characteristic is given by the equation @m = 100 - T where @m is in rad/sec and Tis in N m. The initial motor torque is 10 N · m. A step load torque of 50 N m is applied at t = 0. If the total inertia of the motor load combination is 5 kg · m2, the value of the motor torque after 5 sec is:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Dc shunt generator has the following O.C.C. at 800 r pm Field current (A) 0.5 1 1.5 2 2.5 3 2 3.5 E.M.F (V) 54 107 152 185 210 230 245 Armature and shunt field resistances are 0.1 ohm and 80 ohm respectively .The terminal potential difference falls to 175 V, when the armature current is 100A. find the open circuit volts and the volts lost due to
A dc motor develops 5 N-m of torque at a speed of 75 rad/s when 10 volts are applied. It stalls out at this voltage with 10 N-m of torque. Find the transfer function, G(s) = 82(s)/E.(s). N = 10 ea(t)| Motor J =1 kg-m2 N3 = 10 N2 = 20 J2 = 2 kg-m² | N4 = 20 J3 = 2 kg-m? 0,(1) D
A 230 V d.c series motor has armature and field resistances of 0.5 Ω and 5.0 Ω, respectively. It draws a current of 10 A from the supply while running at 1000 rpm. If an external resistance of 1 Ω is inserted in series with the motor, calculate the new steady-state armature current and the speed. Assume the load torque remains constant. ..
The armature resistance of a DC motor whose poles are made of permanent magnets, connected to a DC voltage source with a voltage of Vt= 627 volts, is 2 Ohm and drives a load of 20 Nm. In the meantime, it draws 4 A current from the source. How many rpm is the steady state speed at this load? (magnetic circuit linear- no saturation and armature reaction effects and mechanical losses will be neglected)
Please show the full solution, thank you
An open-circuit voltage of 480 V appears across the slip-rings of a wound-rotor induction motor when the rotor is locked. The stator has 8 poles and is excited by 60 Hz source. If the rotor is driven by a variable-speed dc motor, calculate the open-circuit voltage and frequency across the slip rings if the dc motor turns a. At 500 r/min, in the same direction as the rotating field b. At 600 r/min, in the same direction as the rotating field c. At 1800 r/min, opposite to the rotating field
A shunt generator delivers 195 A at a terminal voltage of 250V. The armature resistance and the shunt field resistance are 0.02 and 50 ohms, respectively. The iron and the friction losses are equal to 950 W. Find the commercial efficiency of the generator.
Problem-7 A permanent magnet DC motor has an armature resistance of 1 2 and when a voltage of 240 V is applied to the motor it reaches a steady-state speed of rotation of 40 rev/s and draws 80 A. Find the following; a) b) The power input to the motor. The power loss in the armature. The torque generated at that speed. c)
For a DC motor the out put power P.out=300 W, the applied torque is 10 N.m, the :motor speed N in r.p.m is 286.47 rpm O 572.92 rpm 300.25 rpm O 1512 rpm 1206.5 rpm
A long shunt compound generator delivers 100 A at 250 V. The armature, shunt field and series field resistances are 0.02 Ohms, 50 Ohms and 0.05 Ohms respectively. If the Break Horse Power (BHP) or the power developed by the shaft torque of the driving engine is 40, determine the stray loss.
We are studying the use of a permanent magnet DC motor in a roller motion application. The motor has a voltage Vk, an armature resistance Ra, and when it turns a cylindrical roller (load) at n revolutions, it draws a current ia. The torque required by the load is proportional to the angular velocity ω with a proportionality coefficient Kφ. All losses except for ohmic are negligible. ia = 19A, Vk = 230V, n = 380, Ra = 4.5.calculate the mechanical torque delivered to the load (roller),
A motor’s rotor spins at 1,000 rpm when no load is applied (i.e. torque = 0), but reduces to 900rpm when the rated torque of 2.3 N-m is applied. Determine the speed regulation and output horsepower at the rated load condition. If the motor’s input power is 500 Watts at the rated load condition, what is the efficiency?