dn a For a synchronous motor, the maximum value of torque developed at an *angle of 120 degree O 45 degree O degree 90 degree O da A 3 phase, salient pole synchronous motor is fed from an infinite bus and is running at no load. Now if the field current of the motor is reduced to "zero then the Motor will run at synchronous speed Motor will stop Motor will run at low speed Motor will burn * A synchronous motor working at leading power factor can be used as Synchronous induction motor Static condenser Synchronous condenser None of the above

dn a For a synchronous motor, the maximum value of torque developed at an angle of 120 degree O 45 degree O degree 90 degree O da A 3 phase, salient pole synchronous motor is fed from an infinite bus and is running at no load. Now if the field current of the motor is reduced to "zero then the Motor will run at synchronous speed Motor will stop Motor will run at low speed Motor will burn A synchronous motor working at leading power factor can be used as Synchronous induction motor Static condenser Synchronous condenser None of the above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the possible situation that happened if the speed of a synchronous motor reaches the nameplate RPM
The angle between rotor teeth of permanent magnet stepper motor is 1.8° and there are five stator phases in this motor. What is the step angle in degrees of this motor?
A 3-phase, 400/200 V, Y-Y connected wound-rotor induction motor has 0.06 Q rotor resistance and 0.3 Q standstill reactance per phase. To make the starting torque equal to the maximum torque, the additional resistance required in the rotor circuit will be O 0.24 0/phase O 0.42 0/phase O 0.34 Q/phase O 0.52 Q/phase
Q5. Describe the following to protect and control the motors: ine ninouit dio moto oad prot. Dmutuu VII Wnen input (iv) Draw the circuit diagram to explain the adjustable-frequency drive for a 3-phase induction motor
l7 answer 1 2 3
QUESTION 12 An 6.6 kV. three-phase star-connected synchronous motor is working at full load and draws a curren of is-200 A at 0.8 p.f. leading. The armature resistance is 1.20 and synchronous reactance is 60 per phase. The rotational losses are 3 kW. Determine efficiency of the motor. a. 61% b. 67% c. 83% d. 96% e. 73% f. 88% g. 92% h. 78%
A 6 pole, 50 Hz, 3-0 induction motor has blocked rotor reactance per phase equal to four times to the rotor resistance per phase. The speed at which maximum torque developed is rpm.
7
(U.E.L, 0.2) 9. A shunt generator on test is separately excited and driven at 1000 rev/min. The open-circuit test figures are as follows: 0 0157 0477 0 663 0-805 1-0 1-29 12-5 100 300 400 450 500 550 Field current (A) Induced e.m.f. (V) The machine is then shunt-connected and run at 1000 rev/min with a constant field-circuit resistance of 540 , The armature-circuit resistance is 1 0. Deduce and plot the load characteristic of this machine, neglecting the effect of armature reaction. What is the ap- proximate value of the maximum load current? 0. The open-circuit charact
A 2300 V,3 phase,wye-connected synchronous motor has a synchronous reactance of 3 ohms per phase and an armature resistance of 0.25 ohms per phase. The motor operates on load such that the power angle is -15, and the excitation is so adjusted that the internally induced voltage is equal in magnitude to the internal voltage. Determine the armature current
A three-phase, 50 Hz, 10 pole induction motor has a full-load slip of 0.075. What is the speed of a. the rotor relative to the revolving field, b. the revolving field relative to the stator
A three-phase induction motor used for a commercial application in Oman 50HZ runs at 584 rpm at no load and at 546 rpm at full load. a) How many poles do this motor have? b) What is the percentage slip at full load? c) The frequency of the rotor currents when slip is 7 % d) The frequency of the rotor currents at standstill.