12. Arrange the following in order of increasing Ry on thin-layer chromatography analysis plate based on their structure and how they adsorp and separate on TLC plate: Octanoic acid, Butyraldehyde, 2- Octanone, Decane, and 1-pentanol. (Hint: Background information document: What separates the compounds as a chromatogram develops?)

12. Arrange the following in order of increasing Ry on thin-layer chromatography analysis plate based on their structure and how they adsorp and separate on TLC plate: Octanoic acid, Butyraldehyde, 2- Octanone, Decane, and 1-pentanol. (Hint: Background information document: What separates the compounds as a chromatogram develops?)

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter33: High-performance Liquid Chromatography

Section: Chapter Questions

Problem 33.15QAP

See similar textbooks

Similar questions

6. A certain mixture contains the following compounds: propionic acid, 2-hexanol, isoamyl acetate, and 3,4-dimethylheptane. Rank the compounds in the order of decreasing rate of elution using normal phase liquid chromatography. Explain your answer.
A thin-layer chromatography (TLC) experiement was run using three compunds: benzophenone, benzhydrol, and biphenyl. The three solvents that were used with the three compounds were hexane, ethyl acetate, and dichloromethane. Which solvent would be the best for separating these compounds and why?
You spotted a mixture of three compounds, labeled A-C, on a silica plate. The resulting thin layer chromatography (TLC) plate with a mobile solvent mixture of 95 % hexanes and 5 % ethyl acetate is shown below. Which of the spots traveled the furthest up the TLC plate corresponding to spot 3?
Place the compounds in the order they will elute from the column when separated using reverse-phase liquid chromatography (RPLC). CH3 CH3 p-xylene napthalene CH3 anisole OH phenol anisole p-xylene Elutes first Elutes last Answer Bank naphthalene phenol
You are trying to separate a sample with 2 components: X and Y with GC. X has a lower boiling point than Y. Which one has a higher retention time? What is the most common way to increase retention of analytes in gas chromatography?
From the six analytes listed below, n-octanal, n-octane, 1-chlorooctane, n-octanol, n-heptane, and n-octanoic acid predict retention order (shortest to longest retention times) if the SP is: 100% polyethylene glycol or 100% dimethylpolysiloxane.
In an experiment of Reverse Phase chromatography using C-18 stationary phase and a mixture of methanol/ethyl acetate/acetic acid, a researcher tried to separate the 3 compounds shown below. Which compound would have the lowest Rf and which the highest Rf in this experiment? Explain your answer and show any relevant structures.
The following data were obtained by gas-liquid chromatography on a 40-cm packed column: Compound tr, min W, min Air 1.9 Methylcyclohexane 10.0 0.76 Methylcyclohexene 10.9 0.82 Toluene 13.4 1.06 If a resolution of 1.75 is desired in separating methylcyclohexane and methylcyclohexene (Use a spreadsheet to complete this question.) a. how many plates are required? 2798 plates b. how long must the column be if the same packing is used? Length = cm c. what is the retention time for methylcyclohexene on the column of part (b)? Retention time = min
3C. A student is trying to determine the best solvent system to use to separate triphenylmethanol from benzophenone using column chromatography. They have prepared a mixture of standard benzophenone and triphenylmethanol and spotted the mixture on three separate TLC plates for elution in three separate solvent systems. The TLC plates are shown below. For each TLC plate, identify which spot is triphenylmethanol and which spot is benzophenone and calculate the Rf value for the spots on each plate. Based on the TLC results, which solvent system do you think the student should use to separate a mixture of benzophenone and triphenylmethanol by column chromatography? Explain your answer. 100% ethyl acetate 7.6 cm lower spot 7.2cm upper spot 7.4cm 7.5cm 50% ethyl acetate 50% hexanes lower spot 6.1 cm upper spot 7.4 cm 7.4 cm 100% hexanes lower spot 2.7 cm upper spot 3.2 cm
a) What would you see if you ran a Thin Layer Chromatography (TLC) on a mixture of the three solids shown below using silica gel as the stationary phase and ethyl acetate/hexanes as the mobile phase? Whichsolid would have the highest Rf and which would have the lowest Rf? Explain b) Would changing the mobile phase (from part a) and increasing thepolarity by introducing small amount of methanol to the mobile phase change the order ofRf of the above 3 compounds? Explain c) Another type of chromatography is Reverse Phase Chromatography. In this type ofchromatography, the stationary phase is non-polar and the mobile phase is polar. If astudent performed Reverse Phase TLC on the mixture of 3 solids (from part a),what would be the order of Rf’s of the compounds? Which would have the lowest Rf andwhich would have the highest Rf?
The surface of the silica gel has a structure that looks like this diagram below. Suppose you used a plate coated with silica gel, with propanone, CH3COCH3, as the solvent for thin-layer chromatography. Suppose also that the mixture you were trying to identify contained benzaldehyde benzanilide phenol 1) rank the Rf value from large to small 2) name the IMF between each compound and the silica gel OH OH OH -0-Si-O-Si-O-Si-O- O main body of silica structure
Qno1: why there is a need of chromatography and chromatography thecniqs. B) when and where we should use normal and reverse phase chromatography