12 kg of air per minute is delivered by a centrifugal air compressor. The inlet andm3kgтoutlet conditions of air are: V1 = 12 ", P1 = 100 KPa , v1 = 0.5-andV2 = 90", P2 = 800 KPa , v2 = 0.14m. The increase in enthalpy of air passingkgand heat loss to the surroundings is 700KIkgK]minthrough the compressor is 150-Find the work in KW.

Answered: Image /qna-images/answer/0ff716b7-a048-41ab-b302-ee673d4d7197.jpg

12 kg of air per minute is delivered by a centrifugal air compressor. The inlet and m³ outlet conditions of air are: V1 = 12, P1 = 100 KPa , v1 = 0.5- and kg V2 = 90", P2 = 800 KPa , v2 = 0.14 kg The increase in enthalpy of air passing through the compressor is 150 and heat loss to the surroundings is 700 . kg min Find the work in KW.

12 kg of air per minute is delivered by a centrifugal air compressor. The inlet and m³ outlet conditions of air are: V1 = 12, P1 = 100 KPa , v1 = 0.5- and kg V2 = 90", P2 = 800 KPa , v2 = 0.14 kg The increase in enthalpy of air passing through the compressor is 150 and heat loss to the surroundings is 700 . kg min Find the work in KW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/A condenser has vacuum of 70 cm of Hg when barometer reading is 76 cm. Condenser has temperature of 30°C. Air leaks into condenser at the rate of 1 kg air per 2500 kg steam. Calculate (i) the capacity of air pump per kg of steam for removal of air from steam entering condenser, and (ii) the mass of water vapour accompanying this air.
Water is pumped up to 8 m height. The pump operates in steady state, and it is perfectly insulated. Pressure increase over the pump is 850 kPa. The velocity of the water at the pump inlet w is 1 m/s and at the outlet w₂7 m/s. The diameter of the inlet d' is 0.12 m. The water is saturated at the inlet, and the temperature Tis 18 °C. The density of the water is assumed to be constant. The efficiency of the pump n is 77.0 %. Reduce the equation for energy balance with the given assumptions, and calculate the power of the pump and the fraction of kinetic energy. 0 = P + + qmh₂ h₁ + Read from h,s-chart Specific volume of inlet water v Power of pump P 2 w² - w² 2 The share of kinetic energy of the total pump power -2₁)) + g(²₂ — Z₁)
Steam generators are a type of heat exchanges that are used inpower plants to generate steam at desired pressure andtemperature (Fig. Q1.b). In a steam generator, saturated liquidwater at 30°C enters a 60-mm diameter tube at the volume flowrate of 12 L/s. After exchanging heat with hot gas, the waterchanges to steam and leaves the generator at a pressure of 9 MPaand a temperature of 400°C. During this process, the diameter ofthe water/steam tube does not change. Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). (i) Calculate the steam mass flow rate and inlet velocity of the steam? (ii) What is the exit velocity of the steam? (iii) Calculate the rate of heat transfer (in MW) required tochange the phase of liquid water to steam.
Q2/ The Air enters Diffuser at (80 kPa, 27°C) with velocity (200 m/s) and the flow rate (2.5 kg/s), and leaves the Diffuser at (42°C). The exit area of the diffuser is (400 cm2). Determine the exit velocity. from table T1=27.C=300K h1=300.19 kJ/kg T2=42.C%3D315K h2=315.27 kJ/kg
A diffuser is used to increase the pressure of a stream of air circulating at 6500 kg / h. The initial conditions of the inlet are 82 kPa and 197 ° C, and it exits at 115 kPa. The air speed decreases from 245 to 37 m / s as it passes through the diffuser. Calculate: a) The air temperature at the outlet: Response ° C b) The cross-sectional area at the outlet of the diffuser:
A diffuser is used to increase the pressure of a stream of air circulating at 5000 kg / h. The initial conditions of the inlet are 82 kPa and 167 ° C, and it exits at 107 kPa. The air speed decreases from 230 to 42 m / s as it passes through the diffuser. Calculate: a) The air temperature at the outlet: Response ° C b) The cross-sectional area at the outlet of the diffuser: Response m2
Three cubic meter of air at a pressure of 20 kPag and 20 0 C is compressed atconstant volume to a pressure of 425 kPag. determine the following: a. The thermodynamic process the problem representsb. the pressure, temperature, and volume after the processc. change in internal energy, change in enthalpy and change in entropyd. work nonflow and heat transferred
(b) Hairdryer is an electromechanical device that blows ambient or hot air over damp hair to speed the evaporation of water to dry the hair. To design a hairdryer, it should contain the following basic components: a duct of constant diameter with a few layers of electric coils, a small fan to pull the air in and force it through the heating coils. If the density of air is 1.18 kg/m³ at the inlet and 0.90 kg/m³ at the exit, calculate the percent increase in the velocity of air as it flows through the dryer.
1.A gas is undergoing an isothermal process the pressure ratioof the final to the initial state is 2.5 and the cylinder it is stored in is initially2ft3. Find the lengthof stroke(in)if the area of the cylinder is 30in2 2.A cylinder compresses gas isothermally and it 3.Adiesel engine powers a boat. Theengine’s cylinderseachhavea compression ratio(Vmax/Vmin)of 12 and the Vmax is 4ft3.If 1 cylinderis in the isobaric compression stroke,find the final temperature if the initial temperature is 540F 4.A cylinder is heated to cause a piston to move upwards using the expansion of gas inside it. If pressure remains constant, and the initial and final temperatures are 500R and 700R respectively, how much willthe piston move up(in)if the initial volume is 1ft3, and the area of cylinder is 60in2?Neglect the weight of the piston. 5.Agas tank is accidentallyplaced near a heat source. Its bourdon pressure gaugereading was initially 30kpag but after some time the reading became 50kpag. Find the final…
ft-lby 7. One pound of air R = 53.3 4 is compressed isothermally in a closed system from 15 psia and 80°F to 90 psia. Compute the heat transfer.
During the experiment at time 1:40 min, manometer reading is 5 bar and power consumption at ammeter is 3.3 A. Calculate the work done at that particular time and outlet temperature. Ambient condition: 1 bar and 20 °C Equation for the work done, i.e. output work: n n-1 RT. (S W12 = n- 1 n-1 P. T, = T, Given: Polytropic coefficient: n = 1.3 Ideal gas constant: R = 287 kg K %3D kg Density of air at 20°C: p = 1.2041 Volume flow rate: V = 115 L min Motor Voltage: 230 V at 50 Hz What is the inlet temperature in K and the inlet pressure in bar? What is the outlet temperature at time 1:40 min? At time 1:40 min, how much work is done by the piston? What is the input power at time 1.40 min?
A ventilation system includes a fan with a mechanical efficiency of 45% against a static pressure of 30cm WG. If the total pressure created by fan is 300m of air, what is the static efficiency?