11-86. If the overhanging beam is made of wood havingthe allowable tensile and compressive stresses of(m). = 4 MPa and (atm)e = 5'MPa, determine themaximum concentrated force P that can applied at thefree end.-130mm-5 mm200 mm25 mm 25 mm

Free body diagram of the given beam ∑MA = 0By×2 = 3PBy = 3P2∑Fy = 0Ay+By = PAy = P-ByAy = P-3P2Ay…

Answered: 11-86. If the overhanging beam is made…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. The moment area of inertia of the I beam about its horizontal neutral axis is INA= 0.225 x 103 m4. 0= T= 100 mm 300 mm 100 mm Section a-a a 400 KN -0.5 m- 70.2 Mpa (Compression) 37.8 Mpa (Compression) 18.2 Mpa (Compression) 8.9 Mpa 17.8 Mpa 33.5 Mpa 150 mm 200 kN
*9-56. The CX3400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T; = 10"C, determine the average normal stress in cach member when 7; = 45 "C. Alsa, how far will the collar be displaced? The cross-sectional area af each member is 1130 mm. -மீ
The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 14 mm. Assume L = 1.1 m and 0 = 20°. If the average shear stress in the pins at A, B, and C cannot exceed 125 MPa, determine the maximum distributed load Wmax that can be supported by the structure. (1) 0 Answer: Wmax i B kN/m C
If the allowable bearing stress for the material under the supports at A and B is ob = 670 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. P a Answer: Pmax= i b lb
4) Determine the largest mass M of the rigid block which can be supported by the three rods if the allowable stress is 70 MPa for Copper and 140 MPa. for steel.. Copper A=900 L=160m E=120Gla (M) Steel A=12 L = 140mm E=2Gf Copper
The man has a mass of 100 kg and center of mass at G. If he holds himself in the position shown, determine the maximum tensile and compressive stress developed in the curved bar at section a–a. He is supported uniformly by twobars, each having a diameter of 25 mm. Assume the floor is smooth. Use the curved-beam formula to calculate the bending stress.
= 750 psi, determine the maximum load Pmax that If the allowable bearing stress for the material under the supports at A and B is can be applied to the beam. The bearing plates each have square cross sections of 4 in. by 4 in. The reactions at the supports are vertical. Assume w = 550 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= a B b lb
Current Attempt in Progress The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 22 mm. Assume L = 1.5 m and 0 = 25°. If the average shear stress in the pins at A, B, and C cannot exceed 105 MPa, determine the maximum distributed load Wmax that can be supported by the structure. A (1) W L Answer: Wmax i B kN/m
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 a. Determine how much the wire stretches when the horizontal force acts on the pole. 3 ft 30 D 2.5 kip 4 ft B b. Determine the change in the wire's radius c. At what angle is the principal stresses on pole BC? Use Mohr's Circle. d. What is the principal stress in pol BC? Use Mohr's Circle e. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. f. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) g. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. h. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

11-86. If the overhanging beam is made of wood having the allowable tensile and compressive stresses of (m). = 4 MPa and (atm)e = 5'MPa, determine the maximum concentrated force P that can applied at the free end. -130mm- 5 mm 200 mm 25 mm 25 mm