10+j5 8+j6 j25 For the circuit shown below, Take Van = 100 Vrms and the transmission line impedance is 2 ohms per phase. The value of the phase A current is..A. (take Van as your reference) O 12.3<23.7 O 5.6<98.5 O 2.17<-54.7 O 7.69<-22.6 O 9.12<76.5 O 21.8<82.4 O 6.13<-45.3 none of the above

10+j5 8+j6 j25 For the circuit shown below, Take Van = 100 Vrms and the transmission line impedance is 2 ohms per phase. The value of the phase A current is..A. (take Van as your reference) O 12.3<23.7 O 5.6<98.5 O 2.17<-54.7 O 7.69<-22.6 O 9.12<76.5 O 21.8<82.4 O 6.13<-45.3 none of the above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A single phase overhead transmission line delivers 1100 kW at 30 kV at 0.8 p.f. lagging. The total…

A: Given Data: P = 1100 W V = 30 kV pf = 0.8 lagging

Q: The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase…

A: The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance…

Q: The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is…

Q: A 69 – kV, 3 – phase short transmission line is 16 km long. The line has a per phase series…

A: Given Sending end voltage VS =69 KV Line length l =16 km Series impedance ZS=1.125+j0.4375 Ώ/Km…

Q: A Single-Phase Line has an Impedance of 5.75∠56° Ω and supplies the load with 150 A at 3400 V and…

A: Given data: Z=5.75∠56° ohm Ir=150A cos ϕr=0.84 lag

Q: A 60 Hz, 230 mile, three-phase overhead transmission line has a series impedance of o.8431…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: 6. A single-phase 50 Hz generator supplies an inductive load of 5000 k W at a power factor of 0.707…

A: NOTE- “Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: A three phase, 60 Hz, 60 km long transmission line has series impedance Z=0.1+ j 0.5Ω/ km delivers…

A: As per the guidelines, we need to solve only first 3 questions. We need to solve ABCD parameters,…

Q: For the system shown in figure, the line impedances are as indicated in per unit on 100MVA base.…

Q: A three-phase transmission line is 200 km long. It has a total series impedance of (25+ jl 10)2 per…

A: Given: A three-phase 200 km long transmission line has: Total series impedance, Z=(25+j110) Ω per…

Q: A lossy transmission line of length 5 m has a characteristic impedance of (20 + j15)ohm. When the…

A: Given data Length is L = 5 m Characteristic impedance is Z0 = 20+j15 ohm Input impedance is Zin =…

Q: Q3. The ABCD constants of a three-phase transmission line are A = D= 0.936 Z0.98° B = 142.0 Z76.4° Q…

Q: The RL (Resistive and Inductive) Load in the Load Side Section of the Distribution Line Simulator is…

A: This question is based on the load connection in the distribution line simulator. RL load in the…

Q: A 300 Km transmis line with the following series impedance and shunt admittance, z= (1.9+j7.9)x10-2…

A: The solution is given below

Q: The characteristic impedances and lengths of the line sections are indicated in the figure below.…

Q: A 500-kV 60-Hz three phase transmission line is 463 km long. The series impedance is z=0.06+j0.4 2…

A: The solution is given below

Q: A three-phase, 50 Hz power transmission line is 220 km long. It has a total series impedance of…

Q: A single phase transmission line is delivering 450 kVA load at 12 kV. Its resistance is 4.5 and…

A: Given,R=4.5ΩXL=6ΩcosϕR=0.9lagV.R.=Vs-VRVR×100 .....(1)Sending end voltage,…

Q: A 69 – kV, 3 – phase short transmission line is 16 km long. The line has a per phase series…

A: Given data, VSL-L=69 kVZ=1.125+j0.4375 ΩL=16 km

Q: A ( single phase transmission line 100 km long has the following constants Resistance/km 0 · 25 Ω…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: A C Tr 20 km 50 km Ea в Eb Ke Ee PA PB Pc KB Pr The 150 kV energy transmission line whose single…

A: According to bartely be policy only three sub parts are to be answered.kindly repost remaining sub…

Q: A single-phase overhead transmission line delivers 200 kW at 20 kV at 0.8 p.f. lagging. The total…

A: In the question, A single phase overhead Transmission line have resistance R= 20ohm Inductive…

Q: A 50 km, 50 Hz three-phase transmission line has a resistance of 0.01 Q/km and an inductance of 63.6…

A: The solution is given below.

Q: A 500-kV 60-Hz three phase transmission line is 463 km long. The series impedance is z =0.06+j0.4 2…

A: Hi

Q: For the 3-phase, 3 wire system below. Compute for the line currents, total real power, total…

A: Power factor: The power factor tells how much active power is utilized by the circuit from the…

Q: 100 Vi = 1.025/0° V3 = 1.03/1.36851° 300 1 Z13 90.51 Slack 136.93 Z12 Z23 2 V2 = 1.001243L-2.1° 400…

Q: 4. A three-phase 500kV 60HZ, 700km, completely transposed line has the following positive- sequence…

A: Given 500 kv , 60 Hz , 700 km = L z=0.01+j0.3 Ω/km = 0.3∠88° Ω/k my = j3x10-6 s/km For nominal π…

Q: The reactance diagram of the power system network is shown in figure below, where the impedance is…

Q: A 370 kV, three phase transmission line with a 410 km length. The series impedance Z =(0.45+j0.94)…

A: 370kV, 3 phase transmission line Series and admittance parameters are given. Find. The T and π…

Q: The bus impedance matrix for the 3-bus system is: 30.183 j0.078 j0.141 Z- 30.078 j0.148 0.106 j0.141…

A: In this question we need to find a new term of Z12 .

Q: Q1) For the circuit shown below, Vab = 240415°, Zy = (12 + j15) 2, the phase sequence is positive.…

A: given data Vab=240∠15 Zy=12+j15

Q: In the system given below, transmission line impedances are Z1=(25+j5) Ω, Z2=(75+j15) Ω, Z3=…

A: In the system given below, transmission line impedances Z1=(25+j5) Ω, Z2=(75+j15) Ω, Z3= (100+j20)…

Q: A 3-phase, 208V system supplies a delta load with impedances ZAB = 150 235°, ZBC %3D - 12Ω /20ο and…

A: In this question, Three phase Delta unbalanced impedance is given. Find the line currents, active…

Q: A 500-kV 60-Hz three phase transmission line is 463 km long. The series impedance is z=0.06+j0.4 2…

A: Here, we have given some information about a transmission line, which is 463 km long. So, we have…

Q: 6. A single-phase 50 Hz generator supplies an inductive load of 5000 kW at a power factor of 0.707…

A: Total resistance of the line, R= 20*0.0195 = 0.39Ω…

Q: The line-end phase-to-phase voltage of a short three-phase 50Hz transmission line is Ur=31.5 kV.…

A: The line-end phase-to-phase voltage three-phase 50Hz transmission line Receiving end voltage…

Q: 5. A single-phase 50 Hz generator supplies an inductive load of 5000 kW at a power factor of 0.707…

Q: b. A transmission line of characteristic impedance 60 2 is terminated by antenna of impedance 48-j54…

A: Load impedanceZL=48-j50Ω as an antenna will act as loadCharacteristic impedance Zo=60Ωi Voltage…

Q: Vs 3Ω j4 N Vc 3Ω j4 N VR Is Ic IR 80 Ω j 5-106 siemens j60 N

A: Given that the receiving end end voltage is 154 kV. Therefore, the two port network parameters A and…

Q: A 3-phase line having an impedance of (5 + j 20) ohms per phase delivers a load of 30 MW at a p.f.…

A: Given Impedance=(5+j 20) ohms per phase=20.62∠75.96 Ω/phase Power P=30 MW lagging Power factor…

Q: 3.2 A distribution line has an impedance of Z = 6.73+j4.87 N. The receiving-end line-to-line voltage…

A: Regulation of transmission line: Voltage regulation of a transmission line is the rise in…

Q: 1. A 3-phase line having an impedance of (5 + j 20) ohms per phase delivers a load of 30 MW at a…

A: Given: Impedance of transmission line, Z=R+jX=5+j20 PL=30 MWcosϕ=0.8VR=33 kVVS=33 kV

Q: Vz-0.98 - 0.06 j Z12 400 MW 250 Mvar Z13 Z4 24 Slack Bus 3 V = 1.05+0.0j V - 1.0-0.05j Va- 0.95 -…

Q: 15MVA 11kV T2 3 M jo.15 pu Line (200+j500) 0 20MVA ΔΥ YA 11kV 25MVA 20MVA Load j0.15 pu 12.5/132kV…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: 13 10+is 25 For the circuit shown below, Take Van = 100 Vrms and the transmission line impedance is…

A: In this question, choose the correct option What is the real power in the phase B.

Q: If a 3-phase short circuit occurs in one of the two circuit of transmission line at point F, and the…

A: Given: A 3-phase short circuit occurs in one of the two circuits of the transmission line at point…

Q: A three-phase transmission line has an impedance of 2 + j8 Ω per phase. The line supplies the…

Q: The load impedance can be adjusted to the transmission line in accordance with the figure by using a…

Question

A
10+j5
8+j6
j25
For the circuit shown below, Take Van = 100 Vrms and the transmission line impedance is 2
ohms per phase. The value of the phase A current is..A. (take Van as your reference)
O 12.3<23.7
O 5.6<98.5
O 2.17<-54.7
O 7.69<-22.6
O 9.12<76.5
O 21.8<82.4
O 6.13<-45.3
O none of the above

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Transmission Line Parameter and Scattering Parameter (S-parameter)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
The open circuit and short circuit impedance of a transmission line are 200 ohm and 50 ohm respectively. What will be the characteristic impedance of the transmission line?
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
A balanced, 3-phase, 346.41 Vrms line voltage source feeds two loads connected in parallel with a 3-phase line with j3ohm/phase impedance.The first load is Y (star) connected and has an impedance of 12ohm/phase.The second load is D (delta) connected and has an impedance of 12ohm/phase.Taking the Van phase voltage as reference: a)Find the current, active power and reactive power provided by the source. b)Find the phase and line voltages on the loads c)Find the phase currents for each load d)Find the active and reactive power in each load. e)Find the active and reactive power loss in the line f)Show whether the total active and reactive power provided by the source is equal to the total active and reactive power in each load and line.
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
Quest- A single phase 50 Hz, system supplies an inductive load of 5000 kw at power factor 0.8 lag through a line 25 km. Resistance of the line is 0.0195 2/km and inductance = 0.36 mH/km, receiving end voltage is 10 kV. A capacitor is connected across the load to get the voltage regulation of 10%. Ratio of transmission line loss with and without shunt capacitor is
A 132 Kv, 50 Hz, 3-phase tensmission line delivers a load of 5omw at 08 lagging Pf. the transmission line have: A-D: 0 95 Lu" 190 C-0. Ool5 B-96 using Nominal Tto Calculade: regulation of the line and charging Curent?
Derive the equation for impedance and phase shift for series RLC circuit connected to the AC supply.Also draw an impedance triangle and voltage triangle.
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
Derive the relation of SWR in terms of ZL (load impedance) and Zo (Characteristic impedance)