100 mm x 100 mm x 100 mm cube made with glass polymers in the y- direction is subjected to a tensile load of 100 kN along the y-direction. However, the cube is constrained against deformation in the x and z directions. Given the following properties: Ex = 20 GPa Ey = 50 GPa Ez = 20 GPa vxy = 0.25 vxz = 0.5 vyz = 0.25 (a) Compute for the change in length of the cube in the y-direction and; (b) Determine the stresses, σx, σy, σz

100 mm x 100 mm x 100 mm cube made with glass polymers in the y- direction is subjected to a tensile load of 100 kN along the y-direction. However, the cube is constrained against deformation in the x and z directions. Given the following properties: Ex = 20 GPa Ey = 50 GPa Ez = 20 GPa vxy = 0.25 vxz = 0.5 vyz = 0.25 (a) Compute for the change in length of the cube in the y-direction and; (b) Determine the stresses, σx, σy, σz

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

1.7C1 1.4C1 ci 0.9C1 Uniform plastic elongation Necking Elastie 0 4 % 15% 35% Strain in % Stress-Strain diagram Stress in MPa
The Young's modulus of a material is 125 GPa and Poisson's ratio is 0.25. The modulus of rigidity of the material is
If an isotropic material has a Young's modulus of 120 Gpa and a Poisson's ratio of 0.3, calculate its shear modulus. Select one: O G= 25 Gpa O G= 46 Gpa O G = 77 Gpa O G= 39 Gpa O G= 29 Gpa
The is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without breaking. What is the minimum radius that the rope must have if it is .5kg and .6 meters long? The Young’s modulus for this material is 35*10^9 Pa.
Diameter 14 mm, length 100 mm aluminum wire sample, axial When a load of 80 kg is applied in the tensile direction, the change in length and Calculate the change in diameter.(Ealuminum=70 Gpa)
4. The maximum stress a human tendon can withstand is estimated to be 1200 MPa. If you were to test it for rupture what load cell you should use (25ON or 5kN) what problems may occur if you select an incorrect load cell. 5. The figure below is a J-shaped (or concave upward) stress-strain curve. What does a J-shaped stress stain curve indicate about a material's response to stress and tendency to yield? Name two materials that have J-shaped stress strain curves.
(A A\ Find the toughness for a metal that experiences both elastic and plastic deformation. The modulus of elasticity is (15 x 10 psi), and that elastic deformation terminates at a strain of (0.007). For plastie deformation the values for K and n are (221,000 psi) and (0.15), respectively. Furthermore, plastic deformation occurs between strain values of (0.007) and (0.60). إضافة ملف
A cylindrical material that has a Young’s Modulus of 2.5 GPa that is loaded along its longitudinal axis and increases from to .650 mm to .696 mm in the direction of the load. The diameter of the material decreases .05 mm from its 3 c diameter. Assume the material is isotropic. What is the tangential/shear stress during this loading period (in kPa)
A steel rod with a cross-sectional area of 150 mm² is stretched between two fixed points. The tensile load at 20°C is 5577 N. What will be thestress at 25°C?
A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is 200 MPa, the change in the strain is 0.001. Calculate the modulus of rigidity if the poisson's ratio is 0.3.
! How to compute the strain displacement matrix for each element?
One spring is placed inside the other, not touching each other, and compressed between a pair of parallel plates until the distance between the plates is 40 mm. Make a neat detailed sketch of the spring and plate assembly. If G = 83 GPa for both springs, calculate the following: 1. The force applied to the spring assembly. 2. The shear stress induced in each spring. 3. The total strain energy stored in the spring assembly. 4. The stiffness of each spring. 5. The equivalent stiffness of a single spring that can be substituted in place of these springs.