VASSESSMENT PROBLEMObjective 2-Understand the condition for maximum real power delivered to a load in an ac circuit10.7 The source current in the circuit shown is3.6 mH3 cos 5000t A.a) What impedance should be connectedacross terminals a,b for maximum averagepower transfer?b) What is the average power transferred tothe impedance in (a)?c) Assume that the load is restricted to pureresistance. What size resistor connected$2005 µF4ΩAnswer: (a) 20 – j10 N;(b) 18 W;across a,b will result in the maximum aver-(c) 22.36 N;age power transferred?(d) 17.00 W.d) What is the average power transferred tothe resistor in (c)?NOTE: Also try Chapter Problems 10.41, 10.48, and 10.62.

Answered: Image /qna-images/answer/498bf9e7-f356-430a-ad30-e889144b3bba.jpg

Answered: 10.7 The source current in the circuit…

10.7 The source current in the circuit shown is 3.6 mH 3 cos 5000t A. a) What impedance should be connected across terminals a,b for maximum average 20 N power transfer?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Given the circuit, solve for:a. Total currentb. Total apparent powerc. Total real powerd. Total reactive powere. pf of the circuitPlease, I need a complete solution. I promise to give it a thumbs up! :)
Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VTI and VR. b) Find the conduction angle (6). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current. T Zoom
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
A 120 V, 60 Hz power source is connected across an 800 ohm resistance in series with an unknown capacitor. The voltage drop across the resistor is 102 V. Find the, a.) current of the circuit b.) impedance of the circuit c.) Capacitive reactance d.) capacitance value.
1. For the circuit in Figure 1: a) What is the RMS-value, zero-phase angle and frequency of voltage source e(t)? b) What is the total impedance of the circuit? c) Calculate frequency domain voltage Uc and current It (present solution in po- lar form x < yᵒ). d) Calculate time domain voltage uc(t) and current ito(t) (present solution as sine- wave function of time) e(t) = 170 sin (100nt +25°) V, R/= 102, C = 15 μF Answers: Ztor 212.422-87.3°, tot 0.57 AZ112.3°, ito(t)=0.8 sin(100xt+112.3⁰) This homework is to be presented during exercise 14 on 24.4-28.4. Bonus question: Calculate value of voltage e(t) and current isot(t) when /= 1s. Extra points can be earned by solving this question, however it is not mandatory. e(t) ↑ Utot Figure 1. R UR C HH Uc
Consider the two industrial loads that are connected to the source as shown in Figure. We would like design a compensation system to correct the power factor as seen from the source. The Source and the feed line between the source and 40kW source is not accessible, but the feed line between the loads is in the factory, although it is fixed (you cannot change it). The voltage across the 18kW load must be kept constant at 220V(rms).(a) Calculate the value of Vs, without compensation.(b) How must we connect the compensation capacitor(s) to the system? Possible choices are:Between the terminals ofi. the source,ii. the 40kW load,iii. the 18kW load,iv. both loads,v. the source and both loadsJustify your answer.(c) We want to set the power factor of the source to 0.96 (lagging). Calculate the impedanceof the capacitor(s) required, according to choice you made in part (b). The frequency ofthe operation is 50HZ
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Real power and voltage magnitude are the quantities specified for ................... bus.
You have been asked to investigate the loading effects on an alternator supplying a load and also charging a car battery at the same time. The output of the alternator has been rectified to smooth dc, and the circuit is shown below. Using Kirchhoff analysis, determine the initial current in each section along with its direction and the potential difference across the load.
The peak amplitude of the sinusoidal voltage source in the circuit shown in the figure is 180 V, a phase of 0 degrees, and its frequency is 5000 rad/s. a)Find VTH and ZTH for the thevenin equivalent circuit. b)Draw the thevenin circuit. c)Calculate the average power delivered to the load (between points a and b) when the load consists of a resistor and capacitor with RL=2000 0 and CL=0.2 uF. d)Determine the settings of RL and CL that will result in the most average power being transferred. e)What is the average power in (c)? Is it greater than the power in (a)? 6 kN 0.6 H a Vg 12 k2 9. +