10.16 ●● A 12.0-kg box resting on a horizontal, frictionless surface is attached to a 5.00-kg weight by a thin, light wire that passes over a frictionless pulley (Fig. E10.16). The pulley has the shape of a uniform solid disk of mass 2.00 kg and diameter 0.500 m. After the system is released, find (a) the tension in the wire on both sides of the pulley, (b) the acceleration of the box, and (c) the horizontal and vertical components of the force that the axle exerts on the pulley. 12.0 kg 5.00 kg

10.16 ●● A 12.0-kg box resting on a horizontal, frictionless surface is attached to a 5.00-kg weight by a thin, light wire that passes over a frictionless pulley (Fig. E10.16). The pulley has the shape of a uniform solid disk of mass 2.00 kg and diameter 0.500 m. After the system is released, find (a) the tension in the wire on both sides of the pulley, (b) the acceleration of the box, and (c) the horizontal and vertical components of the force that the axle exerts on the pulley. 12.0 kg 5.00 kg

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter12: Rotation I: Kinematics And Dynamics

Section: Chapter Questions

Problem 75PQ

See similar textbooks

Similar questions

One end of a uniform4.0-m-long rod of weightw is supported by a cableat an angle of θ = 37° withthe rod. The other endrests against a wall, where itis held by friction. (See Fig.P8.36.) The coefficient ofstatic friction between thewall and the rod is μs = 0.50.Determine the minimumdistance x from point A atwhich an additional weight w (the same as the weight of therod) can be hung without causing the rod to slip at point A.
Help me please The force-torque system acting on O is equivalent to the key acting on A. If R = 600i + 1400j + 700k lb and | C | = 1200 lb ⋅ pie, determine CR
A 2Hp motor rotates at 1500 rpm. If the allowable torsional stress is not to exceed 50 MPa, what is the minimum diameter of shaft?
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is 0.30 and the weight of the handle is 15 N. Determine the force P that must be applied to the end of the handle to resist a maximum toraue of 75 N m if the torque is applied Clockwise. mm 60 80 80 240 mm mm mm mm
A 9.0 m long uniform rod with a weight of 8 N has 3 masses hanging from it; a 4N mass 1 meter from the left end, a 2 N mass 6 meters from the left end and a 3 N mass 4 meters from the left end. How much force must be applied to bring the rod into total mechanical equilibrium? Where must it be applied?
ull vodafone TR ? 21:52 A aybuzem.aybu.edu.tr Soru 2 Doğru 5,00 üzerinden 5,00 notunu ver P Soruyu işaretle A1 kg block is attached to vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown and the tension upper string is 100 N. What is the centripetal force (F,) acting on the block? (g = 10") 2.0 m 2.0 m 1.0 kg A B D 2.0 m 70 N 136 N 156 N 108 N 80 N Lütfen birini seçin: A E Cevabınız doğru. Doğru cevap: C
A steel wire 2 mm diameter is held between self aligning bearings. The wire weighs 0.241 N/m and the flexural stiffness is 0.157 N.m2. If the highest critical speed is 5000 RPM with the length of the wire 1.0m, what is the approximate number of mode (n=?).
In the figure, a motor weighing 3000 N hangs on a chain attached by an O-ring to two other chains, one attached to the ceiling and the other to the wall. Calculate the tensile force acting on the chain attached to the wall. Consider that the weights of the chains and the ring are negligible.
A pair of parallel helical gears consists of a 20 teeth pinion meshing with a 100 teeth gear. The pinion rotates at 720 rpm. The normal pressure angle is 20°, while the helix angle is 25°. The face width is 40 mm and the normal module is 4 mm. The pinion as well as the gear is made of steel 4OC8 (S treated to a surface hardness of 300 BHN. The service factor and the factor of safety are 1.5 and 2 respectively. Assume that the velocity factor accounts for the dynamic load and calculate the power transmitting capacity of gears. = 600 N/mm?) and heat
The masses 'm' are directly connected to one another by two parallel and identical close coiled springs, one on either side. In the position shown in figure below, with the mass arms parallel to the axis of rotation, the equilibrium speed is 800 r.p.m. Given ball circle radius – 70 mm; length of ball arm = 85 mm and length of sleeve arm = 50 mm. 1. When the speed is increased by 4% without any change of radius for the given position, an axial force of 30 N is required at the sleeve to maintain equilibrium. Determine the mass of cach ball.
ysics.com/m.. E MasteringPhysics: Homework 9 G A uniform, 255 NN rod • Part B HW is now moved 30.0 cm to the right, how far must the fulcrum be moved to restore balance? Express your answer with the appropriate units. 225 N HA ? Az. 69,82 cm ст Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining MacBook Air esc 80 888 12 23 24 & 1 2 4. 6 7 8 %3D Q W E R T Y U { tab P A S F G H J K caps lock C V B M hift control option command command option
A circular loop of thin wire of radius 5/pi cm is suspended from one arm of a balance. The plane of the loop is in contact with the surface of soap solution. The pull on the loop due to S.T. is found to be 0.8 x 10-3 kg-wt. Calculate the S.T. of a soap solution, assuming its angle of contact to be 0 deg.