10. A 150 mV level is to be converted into an 8-bit digital code. Calculate the resolution of the conversion, and analog levels represented by the MSB and LSB, and determine the analog level represented by 11111111.

10. A 150 mV level is to be converted into an 8-bit digital code. Calculate the resolution of the conversion, and analog levels represented by the MSB and LSB, and determine the analog level represented by 11111111.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: In the SCR triggering, the following element used to isolate the high power line from the electronic…

A: As per the guidelines of Bartleby we supposed to answer first question only.

Q: 6.q1.t2

A: The resolution of a D/A converter is the smallest change in voltage that can be produced by a 1 bit…

Q: A 4:1 transformer is connected to a bridge rectifier circuit with a lkn load. What is the peak…

Q: Addressing mode H.W.1 1. What is the addressing mode of each of the following instructions: a-mov…

A: According to the given question, it is required to determine what type of addressing mode is given…

Q: A platinum RTD PT100 measures 103.8 Q at 0 °C and 139.1 Q at 100 °C. Calculate the Temperature…

A: Given data : The resistance at 0° R0=103.8Ω The resistance at 100° R100=139.1Ω

Q: The GTO (Gate turn-off) thyristor is a- O PNPN device O PNPNP device PN double junction device PNP…

A: Here GTO is given and we have to found how many it has PN junction

Q: De fine time constant (I) for (R-L) cct.

A: The time constant (τ) for an RL (resistor-inductor) circuit is calculated using the…

Q: A Resistance Temperature Detector (RTD) PT100 has the output resistance of 100 Q when the…

A: Given Ro=100 Ω∆t=100°CR100=145.6°CRt=130 Ωα=0.00456

Q: For the circuit shown in Figure B23, a = 0.94, calculate the following: i. Collector current (Ic)…

A: α=Collector currentEmitter current. Using above relation we will find currents in BJT. We will apply…

Q: Which of the following diodes uses a metal-semiconductor junction? Oa. Fast recovery diodes b.…

A: In Fast recovery diode, general purpose diode and inverter grade diodes uses simple P-type and…

Q: Create the Diode Characteristic Curve for this data values. Diode Voltage (VD) Diode Current (ID)…

A: Given, Diode voltage, VD (in volts) Diode current, ID (in Amperes) 1.374 8.626 1.279 6.721…

Q: the resistance

Q: Determine the % resolution of a 10-bit A/D converter for a given reference voltage of 100 volts.

A: According to the question we have to calculate % resolution.

Q: The Excess-3 value of (0111.1010) 2 is

A: Excess 3 code of the given Add 0011 in each four bit

Q: 6. Draw the circuit diagram and find the value of 'X' bit for a digital to analog conver, if Vout…

A: According to the question we have to draw the circuit diagram and find the value of 'X' bit for a…

Q: Using Flash ADC method to convert the analoge voltage signal to digital (3-bit) ,where Vi=5V and…

Q: 6.q1

A: To solve the given problem for an 8-bit Digital to Analog (D/A) converter with an output voltage…

Q: Why the gate and cathode of GTO are interdigited? O a. Maximize cathode periphery O b. Create space…

A: The gate and cathode of GTO are interdigited To maximize cathode periphery To minimize the distance…

Q: A 5-bit flash converter has a reference voltage of 16 V. What is the center code voltage for a…

A: The solution is given below

Q: What kind of circuit is shown in the figure? Q16Fig1.gif O 1.Low-pass filter O 2.High-pass filter…

A: As per Bartleby policy we can answer only one question at a time. So I am solving first ques for…

Q: a) Explain how an AC Voltage controller can be design using one SCR and diodes. b) Draw and explain…

Q: ) The dual slope method, it’s the popular method for converting an analog voltage into a digital…

A: Dual-slope method is used for converting analog voltage into digital voltage . ADCs is used in high…

Q: CHOICE QUESTIONS 1. An SCR is a semiconductor device which consists of (a) four PN junctions (b)…

A: Since we only answer up to 3 subparts, we will answer first 3. Please resubmit the question and…

Q: The SCR operation characteristic is plotted for la (anode current) vs lg (gate current), Va (anode –…

A: Silicon Controlled Rectifier (SCR) is the most important and widely used member of the thyristor…

Q: 2- Determine the resolution for each of the following D/A converters: (a) 4– bit (b) 6– bit (c) 18 –…

Q: For the circuit shown in Figure B23, a = 0.94, calculate the following: i. Collector current (Ic)…

Q: 3. For a JFET, this voltage describes the Vds bias needed to start to close off the channel regior…

A: In this question , we have to write which voltage describes the Vds bias needed to start to close…

Q: Schematic Symbol. Label each symbol completely.

Q: 6.q1

A: The resolution of a D/A converter is the smallest change in voltage that can be produced by a 1-bit…

Q: 14 Which of the following is true? O Most often, the PFC circuit is a combination of diode rectifier…

A: PFC : PFC is a power factor correction circuit which is used to improve the power factor of the…

Q: The ----- terminal of the JFET is the equivalent of the Collector terminal of a BJT. a. Drain O b.…

A: In this question, Choose the correct option What is terminal of the JFET is the equivalent of the…

Q: State whether the following statement is true or false. “When an LDO is used as a sub-regulator in…

A: Low dropout (LDO) is an linear regulator which is used for low input and output voltage. It is…

Q: Consider a full wave bridge rectifier, whose transformer secondary voltage is 130sinwt. If the…

Q: For the BJT circuit shown in Figure b, find the operation point of the transistor. (use B=100 for…

A: Solution: The modified circuit is,

Q: Explain the concept of mixed-signal microchips and their importance in interfacing between analog…

A: Mixed-signal microchips, also known as mixed-signal integrated circuits (ICs), are a class of…

Q: Q) The dynamic characteristics of the 1 point measurement instrument are act ----- The linearity of…

A: solve

Q: Explain in your own words some of the trade-offs between CISC and RISC.

A: The architecture of computer has the following types: Reduced Instruction set computer (RISC)…

Q: Follow the successive approximation ADC procedure to convert 3.23456 V

A: ADC- Full form of ADC is analog to digital conversions. And the electronics device used for…

Q: Offset voltage compensating network is connected in between pin of LM741 op-amp number ....... &...…

A: LM741 is an 8-pin operational amplifier. A LM741 op-amp is shown below,

Q: An ideal ADC has a resolution of 6 bits and a conversion voltage range between -2 V and 4 V. What is…

A: Given:- No. of bits, N = 6 Voltage Range = -2V to 4V

Q: H.W: For a five-bit resistive divider, determine: a) The weight assigned to the LSB and also the…

Question

100%

10. A 150 mV level is to be converted into an 8-bit digital code. Calculate the resolution
of the conversion, and analog levels represented by the MSB and LSB, and determine
the analog level represented by 11111111.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

C.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In thyristor triggering, the pulse width should be long enough to permit holding current to be established
For the JFET with maximum drain current 9mA, drain current 2.5mA at gate to source voltage 4V. Calculate the pinch off Voltage.
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
The figure below shows the input waveforms for a NOR latch. Draw the corresponding output waveforms. S A Q
An analog signal voltage in the range of 0 to 8V is divided into 16 equal intervals by a quantizer. What will be the maximum quantization error?
Please review the images.
Create the Diode Characteristic Curve for this data values. Diode Voltage (VD) Diode Current (ID) 0.890904 9.109 0.884515 7.115 0.876023 5.124 0.86333 3.137 0.837654 1.162 0.793023 0.206975 0.779114 0.120885 0.754079 0.04592 0.695273 0.004727 0.599882 0.000118256 0.499998 0.000002487 0.4 5.2464E-08 0.3 1.39E-09 0.2 2.23008E-10 0.1 1.00568E-10 0 0 -0.1 -1.0011E-09 -0.2 -2.00211E-09 -0.3 -3.0031E-09 -0.4 -4.00411E-09 -0.5 -5.0051E-09 -0.6 -6.0061E-09 -0.7 -7.0071E-09 -0.8 -8.0081E-09 -0.9 -9.00911E-09 -1 -1.001E-08 -2 -2.002E-08 -4 -4.004E-08 -6 -6.006E-08 -8 -8.008E-08 -10 -1.001E-07 -20 -2.002E-07 -40 -4.004E-07 -60 -6.006E-07 -80 -8.008E-07 -100 -0.000001001 -200 -0.000002002 -300 -0.000003003 -400 -0.000004004 -500 -0.000005005
A platinum RTD PT100 measures 100 Q at 0 °C and 139.1 Q at 100 °C. Calculate temperature in °C if Temperature Coefficient of RTD PT100 is given as 0.0066 and resistance is 105.2(0). O 7.16 O 7.88 O 10.91 O 8.04
b) Draw a fully labelled block diagram of a demodulator suitable for DSB-AM, DSB-SC, and SSB signals. Explain briefly it's operation, and why a simple diode detector would not have been suitable.
%3D For the circuit shown in Figure B23, a = 0.97, calculate the following: i. Collector current (Ic) ii. Collector-Base voltage (VCB) iii. Emitter Current (IE) iv. Base Current (IB) IE Ic 2.5 k2 Ouput 2.8V IB 10V VEE Vcc Figure B23
1. Draw the output waveform for each technique (a) ASK (b) FSK (c) PSK for binary digits 10011001
Q1) assume A/D converter of counter type uses clock with 100 kHz counter of 8 bit A)determine the total conversion time B)determine the conversion time that is required to generate the sample (111110000)