10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were measured at 0.85 inch. find the maximum load that can be applied if the allowable stresses were 24 ksi for bearing in the plate and 18 ksi for the shear in each rivet. Friction between plates 1/3 the applied.

10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were measured at 0.85 inch. find the maximum load that can be applied if the allowable stresses were 24 ksi for bearing in the plate and 18 ksi for the shear in each rivet. Friction between plates 1/3 the applied.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.1P

See similar textbooks

Similar questions

A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
Connections Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks with a 2" overlap. The glue can carry 125 psi in shear. The wood can carry an axial stress of 1000 psi. How much force P can the joint carry? Sketch and FBD P b a P
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
One plate of size 100 mm x 12 mm is lap joined to another plate of size 200 mm x 12 mm by fillet weld of size 10 mm. Lap length is 100 mm. Fillet weld is provided on all the three sides of the smaller plate. Determine the maximum axial tension the joint could carry. Assume the plates are of mild steel of grade 250 N/mm?.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
P 130 mm 25 mm 25 mm P P 3. Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
Item 2 Figure 1 A D of 1 -0.5 m- 400 KN B -0.5 m C 0.4 m Part A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1100 mm², and a 2014-T6 aluminum post BE having a cross-sectional area of 1700 mm². If a central load of 400 kN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.12 mm between the post BE and the rigid member ABC. (Figure 1) Enter your answers, separated by commas. JAD, CF, OBE = Submit O Π| ΑΣΦ ↓↑ My Answers Give Up vec ? MPa Provide Feedback Continue
The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts (two on each side). Assuming that the load is equally divide among the bolts, determine the normal and shear stresses in a bolt. Express your answer in MPa.
ZAO O "l zain IQ YA docs.google.com/forms 10/.. find the shear stress in bolts 2 3 1. 5 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one 0/10 find the tensile stress in upper plate in section 1-1 (2 (5 (3 1 4) + ...
I Example 2 W SECTION The hanger below (front view and side view) supports a 5000 N partition wall. Calculate the normal stress in the angles if they are 76 x 76 mm with a thickness of 9.5 mm. Calculate the shear stress in the bolts, the bearing stress on the gusset plate and on the angles. PL120X10 220 A325M BOLTS 2- L76x76x9.5 T, O O O O
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in