1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN?

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Determine the distance and resultant of the five parallel forces acting on the rocker arm of the…

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Q3: Each cord can sustain a maximum tension of 500 N, Determine the largest mass (m) of p pipe that…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Let's work through the calculations for the given L-shaped object.### Part a: Finding the x-centroid…

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: Whats the formulae for temperature error %

A:

Q: Q3: Each cord can sustain a maximum tension of 500 N, Determine the largest mass (m) of pip that can…

A:

Q: 3. Tubing used for air-conditioning installations is usually insulated at (a) the low-pressure side…

A: Tubing used for air conditioning installations is usually insulated at the low-pressure because the…

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: Write the equation to calculate the work done by an axial force?

A: Work: Work is defined as the multiplication of the axial force on the body and displacement…

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: Draw longitudinal cross section of the commutator and label each part.

A: Commutator and its diagram and Function.

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: choose the correct answer 200 B. G- A Zero Force members

A: We know that if a joint with two members is not subjected t any external load and also that joint…

Q: Q3/ Determine the resultant of the force system with respect to the point (A)

A:

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: Write the equation that relates applied stress to local maximum stress.

A: Stress concentration factors are generally used to relate applied stress to local maximum stresses.…

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: lestion IJ alculate the maximum stress in 0.10-i 2.00-in dia. Applied torque %3D

A:

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.