1.35 A steel pipe of 400-mm outer diameter is fabricated from 10-mm- thick plate by welding along a helix that forms an angle of 20° with a plane perpendicular to the axis of the pipe. Knowing that a 300-kN axial force P is applied to the pipe, determine the nor- mal and shearing stresses in directions respectively normal and tangential to the weld. P 10 mm Weld -20°

1.35 A steel pipe of 400-mm outer diameter is fabricated from 10-mm- thick plate by welding along a helix that forms an angle of 20° with a plane perpendicular to the axis of the pipe. Knowing that a 300-kN axial force P is applied to the pipe, determine the nor- mal and shearing stresses in directions respectively normal and tangential to the weld. P 10 mm Weld -20°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q) Two steel rods (E= 206.84 Gpsi) are attached to rigid supports at A and B and connected to each other at C, All connections are smooth pins, The rod have (25.4 x25.4 mm) square cross-section, A 444.822 KN vertical force is applied at C. Determine the axial stress and the elongation of rod AC. 274.3 cm 131.9 em 274.3 cm 1444.8 KN
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld. O 611 ksi O452 ksi O 653 ksi O 3.77 ksi O 495 ksl
The steel pressure tank shown has a 751 mm inner diameter and a 9.1 mm wall thickness.Knowing that the butt-welded seams form an angle ? = 50° with the longitudinal axis of thetank and that the gage pressure in the tank is 1.56 Mpa.a. Determine the normal stress perpendicular to the weldb. Determine the shearing stress parallel to the weld
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 16 MPa in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the stresses σn, σt, and the magnitude of τnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise).
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
shown. P1. Two solid circular rods are welded together at B as Determine the normal stress in each rod. 64 mm Ø1 20 KN 38 mm Ø 1.0m 40 KN 40 KN B t Fig.pl-01 1.5 m C whose
A bar of rectangular section shown in is subjected to stresses σx, σy and σz in x, y and z directions respectively. Show that if sum of these stresses is zero, there is no change in volume of the bar.
Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane shear stress and corresponding and normal stress. 100 MPa 150 MPa Tay - 50 MPa