Answered: 1.16 A fluid is pumped into the network…

1.16 A fluid is pumped into the network shown in Fig. P1.16. If Q₂ = 0.7, Q3= 0.5, Q7 = 0.1, and Qg = 0.3 m³/s, determine the other flows.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the mass flow of the fluid if it has the velocity profile shown. The channel is 1.4 m…

A: There are many types of fluids like gas, liquid.it is having more functions like flexibility and…

Q: 4. A horizontal pipe carries cooling water from a reservoir as shown in the following figure. If the…

A: Given: The pipe diameter is 20 cm. The flow rate is 0.06 m3/s. The length of the pipe is 2000 m.…

Q: Water flows steadily through a pipe junction as shown in the diagram. The velocities provided are…

A: Given Data Velocity in pipe-1 (V1) = 5 m/s Velocity in pipe-3 (V3) = 12 m/s Area of pipe-1 (A1) =…

Q: At node A, water enters at a rate of 275li/s and flows out at 5 nodes with different rates namely:…

A: Solution At node A , Q = 275 l/s = 0.275 m3/s At node B , Q = 35 l/s = 0.035 m3/s At node C , Q = 80…

Q: 12.7 The radial component of velocity of water leaving the cen- rifugal pump sketched in Fig. P12.7…

A: Given data:V2=90 ft/sVr2=45 ft/sN=3000 rpm

Q: 1 3 2 Figure Q1

Q: Estimate the flow under the dam below given: k = 5.2x10^-4 cm/s, h1 = 32ft, h2 = 11ft. Answer in…

A: Coefficient of permeability, To find: Flow under the dam.

Q: 3 m P Lower reservoir 100 m 1 m Upper reservoir 10 m

Q: For the flow shown in the figure below, the stream function is = {4ri sin( 0)} where r is in meters.…

Q: aState the three types of flow and explain them.

A: Answer:- Types of fluid flow:- The classification of fluid flow according to their fluidity is…

Q: QI:Fig. shows a pump drawing a solution (specific gravity =1.8) from a storage tank through an 8 cm…

A: For the given pump,

Q: A water jet of velocity 4.2 m/s and a cross-sectional area of 0.50 m2 strikes a curved vane, as…

A: Data given Flow velocity, V = 4.2 m/s Area of flow, A = 0.5 m2 Angle of split = 540 Solution Flow…

Q: -Q.17 MASS FLOW AT A PIPE JUNCTION Consider the steady flow in a water pipe joint shown in the…

Q: As shown in figure 3., water flows through pipe A 1.5 m in diameter at 2.5 m/s and passes through…

A: Diameter of pipe A, DA=1.5mDiameter of pipe B, DB=1mDiameter of pipe C, DC=0.7mVeocity of flow in A,…

Q: Explain the physical significance of the above equation and give the type of jump you would expect…

A: Physical significance of given equation and type of jump between section 2 and 3### Hydraulic jump…

Q: A 150 mm diameter pipe 60 m long connects two reservoirs. Determine the difference in elevation…

A: To Determine The difference in elevation between the water surfaces of the two reservoirs, hL

Q: at a high Reynolds number, for which the velocity profile is approximated by u Uy/R)/8, where U, is…

A: as per guidelines we need to answer only first question

Q: three pipes are connected in series. the first pipe has a diameter of 520 mm and a length of 361 m.…

A: The equivalent diameter of pipe is required. By using Dupuit's Equation

Q: n orifice on the side of a tank discharges water under a head of 9 ft. if the diameter of the…

A: Given: Cc = 0.63, head loss, hL= 0.8 ft. , Water head, H = 9ft diameter of orifice, d = 2'' Find: Q,…

Q: Water flows from a large tank through a large pipe that splits into two smaller pipes as shown in…

A: Given : To Determine :

Q: The flow through a rectangular channel (width in x and height in z) is nonuniform with a velocit…

A: We have to determine the expression for flow rate and average velocity using contants and we have to…

Q: 6. Determine the flow rate and the velocity in each pipe if 4 of the flow goes into pipe 2 with a…

Q: Water flows through the pipe contraction as shown in the figure. The drop in the piezometer level…

A: According to given data Water flows through the pipe contraction The drop in the piezometer level…

Q: Show step by step sol

A: P1= 981 PaV1 = 1.53 m/sExplanation:

Q: Three pipes are connected in series. The first pipe has a diameter of 503 mm and a length of 611 m.…

Q: Q4. A flownet for flow of a dam shown bellow, find the total flow in m³/day if the length of the dam…

A: X = 1.6 m Y = 2.8 m Length = 1200 m

Q: Pipeline 1 Figure Q.1 shows two separate pipelines that con- vey steady flows of air and water,…

Q: Q: Consider the laminar flow near a flat, solid wall, as illustrated in Fig. 2.1. The momentum…

A: Inertial force - FI FI = mass×acceleration⇒FI = ρ×L2×v×v⇒FI = ρL2v2 From Newton's law of viscosity…

Q: Q3) The tank shown in figure Q3 is being filled by pipes 1 and 2. If the water level is to remain…

A: Consider the schematic of a water tank as;

Q: A fluid flows downward with the rate of Q=0.015 m/s in a smooth vertical pipe with the length of l.…

A: Given Data: The rate of flow of fluid is, Q=0.015 m3/s The initial guess is, f=0.02 The density of a…

Q: (Bernoulli/continuity) Water flows into a large tank at a rate of 0.011 m³/s as shown in the figure…

Q: 4. A steel beam, with square cross-section of side 10 mm and a simply supported length of 8.0 m from…

Q: A water reservoir of 300 (Height) x 300 (width) x 500 (depth) m has its free surface at 250 m above…

A: Height of reservoir = 300m Width = 300m Depth = 500m Dia of orifice = 500mm Coefficient of…

Q: The flow through a rectangular channel (width in x and height in z) is nonuniform with a velocity…

Q: For the pipe system shown in figure 2, find the flow rate in all pipes neglecting all minor losses.…

A: It is required to determine the flow rate in pipe C. QC=VC×AC=3.6 msec×π4×0.7 m2=1.39 m3sec It is…

Q: Piezometer Reservoir A Elevation 100 ft Reservoir C Elevation 80 ft Reservoir B Elevation 80 t…

A: Given that, Hazen William's equation with C1=120. Using Hazen William's equation velocity…

Q: Task 1: A dam is used to store water, and a circular gate which is hinged at its bottom edge is used…

Q: As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and…

A: To solve this problem, first we need to calculate the specific gravity. Then the Bernoulli equation…

Q: As shown in the figure, water enters and exits a U-shaped piece of pipe located in the horizontal…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

1.16 A fluid is pumped into the network shown in Fig. P1.16. If Q₂ = 0.7,
Q3=0.5, Q7 = 0.1, and Qg = 0.3 m³/s, determine the other flows.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Determining the flow using continuity and neglecting losses in network.

VIEW

Step 3: Determining the flow using continuity and neglecting losses in network.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. Considering the following figure with flow from A to D, compute the total head loss from A to D if the flow is 1700 liters per second. Pipe 1: Length = 1000 m; = 900 mm; n =0.011 Pipe 2: Length = 650 m; Ø = 450 mm; n =0,011 Pipe 3: Length = 750 m; = 600 mm; n = 0.011 CIL Pipe 4: Length = 460 m; 0= 750 mm; n = 0.011
Please tell whether the statements are True or False.
2.2. A pump adds 40 m against a closed delivery pump, 37 m at discharge of 170 L/s and 25 m at discharge of 340 L/s. a) Calculate the constants bl, b2 and b3 to describe the pump curve mathematically. b) Derive the equivalent pump curve for two pumps in parallel
6. Oil (S=0.92) is transported through the system as shown below. If the pressure head difference between points B and A is (P-P₁)/ pg = 145 m, calculate the horsepower supplied by the pump to the system. Pipe 1 has a diameter of 7 cm and length 38, while pipe 2 has a diameter of 4.0 cm and length 20 m. Assume, a = 1.00 at all locations, and Elev. 1 = 80 m, Elev. 2 = 145 m, and Elev. 3 = 30 m. Head loss in the pipes are given as V²L h=0.017- for pipe 1, and h₁ = 0.022- for pipe 2. Assume that the losses between V²L 2gD 2gD A and B are negligible and are at the same elevation. Hint: Apply energy equation at reservoir surface and exit point. Velocity in pipe 1 can be determined in terms of velocity in pipe 2 using Q₁-Q₂. Thus, pump head can be determined in terms of the velocity. Now apply energy equation at A and B, the elevations of A and B are same, and the pressure head difference is known. Plugging in pump head value in terms of velocity, the velocity in one of the pipes can be…
A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter reduces to 0.74 m. Starting from Bernoulli's equation, estimate the velocity of flow in the reduced section, and the mass flow rate (=pQ) through the duct if the pressure difference between a point upstream of the reduction and another point at the reduction is equivalent to 30 mm of water.
A rectangular concrete channel 5m wide carries water as shown in the figure. The channel bed slope is 0.0022. Find the theoretical rate of flow in the channel.
3 .Consider the incompressible flow of an ideal fluid having a density ρ = 1600 kg / m3 (figure 3). We give: P1 = 2 105Pa, P2 = 3 105Pa, V2 = 1 m / s and V1 = 0.5m / s. Determine the net power of the pump to ensure a volume flow Qv = 0.01 m3 / s.
Solution plz
Que. 5.6 A centrifugal pump having an impeller of 35 cm outside diameter rotates at 1000 rpm. The vanes are radial at exit and are 7 cm wide. The velocity of radial flow through the impeller is 3 m / sec. The velocity in the suction and delivery pipes are 2.5 m/s and 1.5 m / s respectively. Neglecting frictional losses determine the height through which pump lifts the water and the horse 3 - power the pump
Two pumps whose characteristics are given in Sample Prob. 15.13 are to be used in parallel. They must develop a head h = 35 + 20Q2 as in the sample problem. (a) What is the flow rate with both pumps operating at 1800 rpm? (b) The speed of one of the pumps is reduced until it no longer delivers water. At approximately what speed will this happen? Sample Prob. 15.13: The two pumps (n = 1800 rpm) each have the following characteristics: h, ft: 100 90 80 60 40 20 Q, gpm: 0 110 180 250 300 340
Three reservoirs A, B and C are connected by a pipe system as shown in the following figure. The length and diameter of pipe 1, 2 and 3 are 2000m, 1000m, 500m and 30cm, 25cm, 20cm respectively. Find the discharge into or from the reservoir B and C if the rate of flow from reservoir A is 50 lit/s. Find the height of water level in the reservoir C. Take coefficient of friction = 0.005 for all three pipes.
In the flow shown in the figure below, water leaves a large elevated tank and travels through tube 1 (D1 = 10 cm) which divides into two smaller tubes open to the atmosphere (D2 = 3 cm and D3 = 6.5 cm). The pressure indicated by the pressure gauge on the tank is 10 kPa. Determine the flow velocity in tube 1 considering the ideal fluid.