1. What is the equivalent resistance of the resistors in the figure? R₁ = 2.0 Ω R₁=2.02 www R3 = 2.002 2. Find the current in and voltage across the 10 resistor shown in the figure below: R₁ = 102 3. For the circuit shown below, find a) The current in each resistor b) The voltage across each resistor c) The total power delivered V - 20 V R₂ = 2.02 V = 10 V R₂ = 20 Ω R₁ = = 20 Ω R₂=2.02 R3= 5.092 R3-2002

1. What is the equivalent resistance of the resistors in the figure? R₁ = 2.0 Ω R₁=2.02 www R3 = 2.002 2. Find the current in and voltage across the 10 resistor shown in the figure below: R₁ = 102 3. For the circuit shown below, find a) The current in each resistor b) The voltage across each resistor c) The total power delivered V - 20 V R₂ = 2.02 V = 10 V R₂ = 20 Ω R₁ = = 20 Ω R₂=2.02 R3= 5.092 R3-2002

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 37P: Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b)...

See similar textbooks

Similar questions

Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?
A 50resistor is connected across the emf v(t)=(160V)sin(120t) . Write an expression for the current throug1 the resistor.
For the circuit shown in Figure P28.24, calculate (a) the current in the 2.00-11 resistor and (b) the potential difference between points a and b.
Three 100- resistors are connected as shown in Figure P21.41 The maximum power that can safely be delivered to any one resistor is 25.0 W. (a) What is the maximum potential difference that can be applied to the terminals a and b? (b) For the voltage determined in part (a), what is the power delivered to each resistor? (c) What is the total power delivered to the combination of resistors?
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
The circuit in Figure P27.34a consists of three resistors and one battery with no internal resistance. (a) Find the current in the 5.00- resistor. (b) Find the power delivered to the 5.00- resistor. (c) In each of the circuits in Figures P27.34b, P27.34c, and P27.34d, an additional 15.0-V battery has been inserted into the circuit. Which diagram or diagrams represent a circuit that requires the use of Kirchhoffs rules to find the currents? Explain why. (d) In which of these three new circuits is the smallest amount of power delivered to the 10.0- resistor? (You need not calculate the power in each circuit if you explain your answer.) Figure P27.34
A car battery with a 12-V emf and an internal resistance of 0.050 is being charged with a current of 60 A. Note that in this process the battery is being charged. (a) What is the potential difference across its terminals? (b) At what rate is thermal energy being dissipated in the battery? (c) At what rate is electric energy being converted to chemical energy? (d) What are the answers to (a) and (b) when the battery is used to supply 60 A to the starter motor?
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
In the circuit of Figure P28.30, determine (a) the current in each resistor and (b) the potential difference across the 200- resistor.
The following figure shows 3 resistors R = 1.1 kN R2 = 3.3 KN R3 = 1.1 klconnected to a battery source emf E = 5 volts %3D Ri a R2 Rg a) Find the current across R3. Current across R3 Give your answer up to at least three significance digits. A b) Find the voltage across R2. Voltage across R, Give your answer up to at least three significance digits.
A.) Find the equivalent resistance between points a and b in the given figure. B.) Calculate the current in each resistor if a terminal voltage of 41v is applied between points a & b.