1. What is the bending moment at end supports of a simply supported beam? a) Maximum b) Minimum c) Zero d) Uniform 2. What is the maximum shear force, when a cantilever beam is loaded with uniform distributed load throughout? a) wx| b) w c) w/l d) w+l 3. What will be the variation in BMD for th diagram? [Assume | = 2m]. 10 KN B A a) Rectangular bl Tranezoidal

1. What is the bending moment at end supports of a simply supported beam? a) Maximum b) Minimum c) Zero d) Uniform 2. What is the maximum shear force, when a cantilever beam is loaded with uniform distributed load throughout? a) wx| b) w c) w/l d) w+l 3. What will be the variation in BMD for th diagram? [Assume | = 2m]. 10 KN B A a) Rectangular bl Tranezoidal

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Exercise 1: Draw the shear and bending-moment diagram for girder AB. Also determine the maximum bending-moment. Where x = 2020100214
FOR THE TRUSS SHOW BELOW, SOLVE FOR THE STRESSES (ORANGE) IF ALL MEMBERS 750 mm^2.. 3m 2m 2m 2m C 3m E 200 KN 2m G F 100 kN H 4m B
5) work under the loading condition shown. Bars AB and BD have a cross-sectional area of 2 in.?. Bars AC, BC, CD, and CE have a cross-sectional area of 1.5 in.?. Use a modulus of elasticity (E) of 30,000 ksi. Internal forces for the loading condition are given above each bar (C = compression, T = tension). For the truss below, compute the horizontal deflection of point C using virtual 30 kips 37,5 (c) 6 fA 30* (T) 6A 37.5" (c) E (4) ,Sh
A simple beam 4.4 m in span carries a concentrated load of 283 kN at its midspan and is subjected to an axial tensile force of 240 kN. Fy = 248 MPa. Three sections are being considered as follows with their corresponding properties relevant to the problem. Use the formula: (fa/0.60Fy) + (fb/0.66Fy) <1.0 What is the value of the lowest bending stress?
2. The center diagonal of the truss in the figure shown can support tension only. Compute the force of DG and BE. A 20 200 B BD 20% C www.w BE CE D DF F 1===54 25 of 61 20 DG 20 E 15 EG G TR1 R1 600 15 600 300 H R3 R2
Please answer the problem attached image. Hint: a=98.45Mpa
SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P= 210 kN. The diagonal member is on a slope 2V:1H and is connected to a supporting beam by a wide tee. S1= 38 mm t1= 16 mm S2= 75 mm t2= 16 mm S3= 100mm t3= 16 mm Allowable strength and stresses: Yield strength, F,= 248 MPa Ultimate Strength, F= 400 MPa Bolt shear strength, F,= 150 Mpa Bolt Tensile Stress, F;= 195 Mpa Bolt Bearing Stress, F,= 1.2Fu Assume that the bolts are equally Loaded. 1. Determine the required "d," of the 3 bolts in shear connecting the double-angle member the wide tee. Round your answer to whole number. 2. Determine the required diameter "d," of the four bolts in tension connecting the wide tee to the flange supporting beam Round your answer to whole number. 3. Design the diameter "d," of the four bolts connecting the wide tee to the flange supporting beam. Round your answer to whole number. 1p S2 S2 t1 t2 t3 S3
Required information Consider the beam and loading shown. If a=8 in, b=9.0 in, c=1 in. For a section at n-n, determine the shear stress at b. A 25 kips 20 in.- 10 in. 25 kips - 20 in.- B a +6 i in.. in. b b a с in.
4.
Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.67 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 13.8 ft and P = 99.53 kips. Round off the answer to five decimal places.
STEEL DESIGN include free body diagram and detailed solution.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; | = 1960 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 17 kips, LAB = 6.4 ft, LBC = 9.6 ft. AP MA A B C LAB LBC Answer: (a) VA = in. (b) VB = in.