1. Two sizes of culvert pipe are stacked against each other as shown in the figure. The largest pipe at the has a diameter of 500 mm and weighs W kN (see given table for assigned value) while the base pipes are 250 mm in diameter and weighs W/4 kN each. Determine all contact forces and the magnitude of tension in the cable. R=500 mm T=250 mm cable -75 mm

1. Two sizes of culvert pipe are stacked against each other as shown in the figure. The largest pipe at the has a diameter of 500 mm and weighs W kN (see given table for assigned value) while the base pipes are 250 mm in diameter and weighs W/4 kN each. Determine all contact forces and the magnitude of tension in the cable. R=500 mm T=250 mm cable -75 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.) Given the Cable as shown below that supports a 100 N/m uniformly distributed load. Determine the sag d that minimizes the maximum tensile force in the Cable. 30 m B T d 10 m ↓ A ↓↓↓ O ↓↓↓↓↓↓ Wo
Two sizes of culvert pipe are stacked against each other as shown in the figure. The largest pipe at the has a diameter of 500 mm and weighs W 109 kN while the base pipes are 250 mm in diameter and weighs W/4 kN each. Determine all contact forces and the magnitude of tension in the cable. R=500 mm T=250 mm cable -75 mm-
Given The instrument package shown the figure weighs 207 N, and the dimensions are as given. Length = 680 mm Width = 365 mm Height = 369 mm Water surface Width Length Height Cable Sea bottom Required Calculate the tension in the cable if the package is completely submerged in seawater having a specific weight of 10.10 kN/m3. Provide answer in Newtons, to the nearest 10th.
A 509.9N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC which lies in a vertical transverse plane and loops underneath the shaft. Calculate the tension T1 (N) in the cable. Round off only on the final answer expressed in 3 decimal places.
Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?
Problem 8: Values: ● ● ● d₁ = 6.5 ft d₂ = 2.75 ft Force in cable AB = 475 lb Use the dot product to determine the following: a) The magnitude of the force projected along the axis of the pipe (axis AC) b) The angle between the cable and the axis of the pipe (axis AC) X d₂ d₂ d₂ 8 B d₁ A y
A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches 7600 N. B d3 da ds do d₁ d2 Z E D d5 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 8.5 m d₂ 18.5 m 16.5 m 30 m 9 m 80 m a. Determine the magnitude of the force/tension in cord AB, TAB. b. Determine the magnitude of the force/tension in cord AC, TAC. c. Determine the magnitude of the force developed along the tower, FAE- → i. Hint: FAB= (0+03+ FAER) KN. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord TAB is The magnitude of the force/tension in cord TAC is The magnitude of the force developed along the tower FAB is kN kN kN
B The two blocks shown are originally at rest. Neglecting the masses of the pulleys determine the tension in the cable. Given: . • Weight of block A = 220 lbs Weight of block B = 190 lbs • kinetic friction coefficient = 0.55 Find: A • Tension in cable = lbs Your Answer:
Please solve using paper.Problem 10. A ball weighing 20 kg is placed as shown in the figure. If the force F applied horizontally at the ring is equal to 120 N, determine the dimension d so that cable AC experiences 0 force.
From the figure as shown, the cable BC supports the horizontal bar AB. Compute the shear stress at the hinge support at A having 20 mm Ø and at the pin support at B which has 30 mm Ø pin. The given views show how many of shear can be produced. Use 2 decimal places in every solved value. Pls include fbd.