Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?

Q: In the arrangement as shown; Gate 'OA' has width of 2 m inside. Hinge passes through O and rope AB…

A:

Q: Suppose that P= 7 kN. (Eigure 1)

A:

Q: The square steel plate has a mass of 1920 kg with mass center at its center G. Calculate the tension…

A:

Q: R. (400, 200 60N (200 Bol R. R. A table 600 mm by 600 mm is mounted on three legs. Four loads…

A:

Q: A 200-mm diameter pulley is prevented from rotating to 60-mm diameter shaft by a 70-mm long key. If…

A:

Q: Situation 2. Determine the maximum weight of the bucket that the wire can support so that no single…

A:

Q: Please answer urgently Please Provide FBD. Thankyou

A: Given: The weight (W) is 75 lbs. The coefficient of static friction is 0.25. Consider the figure,

Q: A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead…

A:

Q: Problem 3.3 - A force F is applied to one end of a cable of length L. The other end of the cable is…

A:

Q: Let G = 100kg, calculate the unknown loads A and B in order for the whole mechanism to stay…

A:

Q: 9. What will be the slope at point B? 10. What value of load P is needed in order to produce a zero…

A: Given P = 250 kNs = 2mW =-7x +81E = 200 GPaI = 2*109 mm4.It is asked to determine the following,1.…

Q: Learning Goal: To be able to analyze the equilibrium of systems subjected to frictional forces at…

A: For Part A ,find mass of block B,mB=? For solution of part B and Part C figure needed because figure…

Q: 5. Four 1-in.-diameter pegs are attached to a board as shown. Two strings are passed around the pegs…

A:

Q: 8.66 9 B

A: GIVEN DATA:-⇒Length of the gate = 9 m⇒ρ = density= 1000 kg/m3→Gate dimensions:-⇒Width = 9m⇒Height =…

Q: Learning Goal: To replace force-couple systems with an equivalent force by specifying the magnitude…

A: Replace force and couple system with an equivalent force by specifying the magnitude of the force,…

Q: DE TER MINE FORCE IN ROD 12x12 wooD BEAM 10 I = 1728(IN), E I5il STEEL ROD 15' I 60 A : 1.00" E o Ki…

A: Here I am using direct deflection result

Q: A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1…

A:

Q: Determine the maximum safe value

A:

Q: The hoist shown is used in a machine shop to position heavy workpieces in a lathe. If the cable…

A: Given :

Q: measured from point A. (Hint: break-down the trapezoid-shaped distributed loading equivalent…

A: Replace resultant loading of separate uniform load(i.e rectangular or triangular) to the equivalent…

Q: Three cables support a uniform plate. Find the tension in cables A, B, and C, given: F = 1,000 N,…

A: Given data :F = 1000 N , Wplate = 625 N L1 = 4 m , L2 = 4 m  , L3 = 6 mTo find :TA, TB and TC

Q: A crate weighs 810 lb and is hung by three ropes attached to a steel ring at A such that the top…

A: A weight is hung by three ropes , we need to find out the tension in each ropes

Q: A carpenter holds a 10-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board,…

A: Given, W= 10lb Vertical forces are NA&NB, Free body diagram:-

Q: A stepped vertical steel bar ABCD is fixed at the top end A. Each segment of the bar AB, BC and CD…

A:

Q: Determine the maximum shearing stress of the beam shown in the above problem (prob. #2) 5 kN 2 m 2.5…

A: depth h = 200 mm width b = 75 mm udl 2.5kN/m point load = 5kN

Q: Q3: Draw the S.F and B. M. diagrams for the beam shown below. P = 625 lb L1 = 4 ft q = 80 lb/ft L2 =…

A:

Q: A hanging plant with a mass of 10 kg hangs from three ropes as shown. Knowing that Y = 1.8 m and X =…

A: Drawing the Free Body Diagram (FBD):Point A is where the three ropes meet.The forces acting on point…

Q: For the beam supporting the loads, determine the slope and deflection of the free end using AREA…

A:

Q: 1. Ra XW VX Find Ra, Rb, Ma & Mb: WX Draw Shear & Moment Diagram YZ XW Rb

A:

Q: n W or = 3.35 The electric motor exerts a 500 Nm-torque on the aluminum shaft ABCD when it is…

A:

Q: LA B- 50 40 0 350 N

A:

Q: Show how to resolve each force into its x, y, zcomponents. Set up the calculation used to find…

A: (a) Consider the figure,

Q: 2 ft 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at…

A: To find tension in rope and reaction at pin A

Q: Situation 5: A barge is pulled by two tugboats. If the esultant of the forces exerted by the…

A: Given that the resultant force is 5000lb along the axis of barge. Let T1 and T2 are tension in ropes…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

A:

Q: Proble A weight of 100 Ib is supported by two ropes as shown. Calculate the tension in each rope…

A: W=120lb To find tension in rope CA and CB

Q: Blocks A and B in (Figure 1) have a mass of 5.0 kg and 16 kg, respectively. 300 mm PD-0.1 D B 400 mm…

A:

Q: QUESTION 1 Determine the maximum force P that can be applied without causing movement of the 250 lb…

A:

Q: 1. The plate is horizontal, is in equlibrium, and weighs 1450 N. Determine the tension in cables AB,…

A: The given figure is shown below:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.