1. The tank in the figure below can be emptied by removing a 3 cm diameter stopper at the right corner. 20 N of force will cause this stopper to be pushed out of the tank, releasing stored water. For this situation, what will be the reading h on the manometer (manometer fluid SG 13.6)? water 45° h [1 cm Plug, D = 3 cm mercury

1. The tank in the figure below can be emptied by removing a 3 cm diameter stopper at the right corner. 20 N of force will cause this stopper to be pushed out of the tank, releasing stored water. For this situation, what will be the reading h on the manometer (manometer fluid SG 13.6)? water 45° h [1 cm Plug, D = 3 cm mercury

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
A manometer is first filled with water (blue) and then with mercury (gray).The mercury end of the manometer is open to the atmosphere (Fig. 1). Given that the density of water ρw = 1000 kg/m3, and the density of mercury ρHg=1.35 × 104 kg/m3. What is the hydrostatic pressure at point a? Express your answer as a gauge pressure.
Find the pressure magnitude in the Gasoline Pipe at the right side of the figure. Specific weight of water is 9.81 kN/m3 and specific weight of air is negligible. Oil SG= 0.79 Pgage = 376 kPa Gasoline SG = 0.70 Air 45 cm 50 cm Pipe 22 cm † 10 cm Water `Mercury SG= 13.6
The pressure drop of water in a pipe is measured by a manometer using a liquid of density 2000 kg/m³. The difference in height of the liquid in the limbs is 10 cm. Then, the pressure drop is
show complete solution and diagram
I need the answer as soon as possible
Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the pipe with diameters 10 cm and 7 cm and the two sections are connected by a smooth reducing section as shown in the schematic. We use a manometer with glycerin as the manometer fluid (with glycerin density of Pglycerin 1,260 kg/m³) to measure the pressure difference between the two pipe sections. Assume that frictional effects are negligible and consider specific gravity of oil as SGoil = 0.76. What is the manometer reading, h (i.e. differential height of glycerin between the two arms of the manometer)? 10 cm I h T 7 cm-
Problem 1.2 Two water tanks are connected to each other through a mercury manometer with inclined tubes as shown in figure. The value of theta is degree. (Take g=9.81 m/s²) Water (p.= 1000 kg/m³) Tank A P=20 kPa Tank B P = 40 kPa Mercury (P = 13600 kg/m³) 26.8 cm
The fluid 1 in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in figure below. Determine the gage pressure (in kPa) of air in the tank if hj=2.1m, h2=2.9m and h3=1.3m. Take the densities of fluid 1, fluid 2 and fluid 3 to be 1906 kg/m³, 1173kg/m³ and 27357kg/m³, respectively. fluid 2 Air hị fluid 1 h2 h3 fluid 3 2.
In a manometer shown as below, the mercury (SG = 13.6) height difference is 10 cm. If the volume of the gas is 250 mL, how many moles of gas are there on the right side? Assume the temperature is 20 degrees Celsius. Hint: Use the Ideal Gas Law for the relationship between pressure and mole number, PV = nRT. O 1.318 mol O 0.00137 mol O 0.0118 mol O 0.107 mol mercury gas
In the figure shown, originally there is a H2=9 cm manometer reading and H1=15 cm. Atmospheric pressure is 101.3 kPa. what is the absolute pressure at A (kPa)? If the absolute pressure at A is doubled, what then would be the manometer reading (cm) ?
IV. Water is discharged from a device in to air, as shown in the figure. How much is the horizontal force to hold the device. Ignore gravity and viscosity. 1 Ibf= 1 slug ft/s 2, air (2)A=0.4 t 30 fU 10 psi Flang 1/20 tis (1) A=0.8 (E) A- 0.8 n air Water density =1.94 slugs/ft^3.