1. The stress induced in a body when subjected to two equal and opposite pulls is known as: (a) Compressive stress (b) Shear stress (e) Tensile stress (d). 2. The force of resistance per unit area offered by a body against deformation is known as: (a) Resistance (b) Stress (c) Strain (d)... 3. If the external force acts on a body is removed and the body comes back to its origin shape and size, the body is known as : (a) Plastic body (b) Elastic body (c) Ductile body (d) 4. The ratio of change of dimension of the body to the original dimension is known as: (a) Strain (b) Deformation (e) Simple stress (d).

1. The stress induced in a body when subjected to two equal and opposite pulls is known as: (a) Compressive stress (b) Shear stress (e) Tensile stress (d). 2. The force of resistance per unit area offered by a body against deformation is known as: (a) Resistance (b) Stress (c) Strain (d)... 3. If the external force acts on a body is removed and the body comes back to its origin shape and size, the body is known as : (a) Plastic body (b) Elastic body (c) Ductile body (d) 4. The ratio of change of dimension of the body to the original dimension is known as: (a) Strain (b) Deformation (e) Simple stress (d).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(2) lubäi The difference between shear strain and linear strain Linear Strain is change in length/original length while shear strain is the angle of deformation linear strain and shear strain are the same and equal to the change in length / original O length None O linear strain and shear strain are the same and equal to the change in angle under shear force (2) ibäi A concentrated load is one which acts at a point on a beam O varies uniformly over the whole length of a beam
A long steel rod is placed horizontally between two supports, one at each end. The rod bends a little in the center. Which property of this rod can be used to estimate how much the rod should bend at the center? 1. Its Shear Modulus 2. Its Young's Modulus 3. All of these Moduli can be used to compute how much it bends. 4. Its Bulk Modulus.
Question continued... (where the force P1 is equal to 259 lb and the force P2 is equal .to 88 lb) D 5 ft P2 B 12 ft The internal force in member BC is equal to Ib (C) 105.60 Ib (T) 88.00 Ib (T) 132.00 Ib (T) 74.80
Q1: make introduction relating to all topics? 1. Shear force and bending moment on skateboard. (Shear force and bending moment)? 2. Stress and strain in uniaxial solid and hollow bars (stress & strain)? 3. Eccentric loading (bending stress)? 4. Stress in cylindrical pressure vessel (Mohr circle)? 5. Stress and strain due to applied torque (torsion)?
A Given: . 10 A L1 L1 = 3.5m L2 = 5.5m с H = 4.25 m . FC = 25 KN D Fc. L2 Member AC- (magnitude of force) Match the reaction at the support (FAX, FAy, FB), and the forces in each member (AC,AD, CD, BD, BC) Member BC (magnitude of force) Support FAy (include direction, up positive, down negative) Support FB (include direction, up positive, down negative) Support FAX (include direction, left negative, right positive) Member BD (magnitude of force) Member AD (magnitude of force) B Member DC (magnitude of force) 1. -25 2.-19.3 3. -15.3 4. 11.8 5. 0.00 6. 11.8 7. 15.3 8. 19.3 H 9. 20.0
Q1-B // A steel bar has a square section of 10 mm side and a length of 60 mm, subjected to a tension force of 50 KN, as a result the bar has extended 2 mm; Calculate: 1-Yong modulus 2- The engineering stress 3- The engineering sustain 4- The true stress 5- The true strain 6- The percentage reduction in Area
1:02 M Vo) LTE1 . 94% i 90 1. Show that pure shear gives rise to tensile and compressive stresses across the planes inclined at 45° to the shearing planes, the intensity of the direct stresses being of the same magnitude as shearing stress. 2. Show that volumetric strain in a bar is equal to the sum of strains in three mutually perpendicular directions. 3. Explain the terms: (i) Modulus of elasticity (ii) Modulus of rigidity and (ii) Bulk modulus. 4. Derive the relationship between (i) Modulus of elasticity and modulus of rigidity (ii) Modulus of elasticity and bulk modulus II
- 6. A 6 mm diameter rod, of unknown material, is subjected to 10 kN tensile load. In the process, its length increased from 70 mm to 72 mm. If stress is proportional to strain, determine the modulus of elasticity, in GPa, of the material? 10.7 12.4 a. b. C. 19.5 d. Answer is not among the choices 16. How much should an 80-kg person weigh (in Newtons) if he is on top of Mt. Kilimanjaro, which is at 5890 m above sea level? The mass and radius of the earth are 5.9742 x 1024 kg and 6378 km, respectively. Use a universal gravitational constant of 6.67 x 10-11 m³/kg-s² a. 782 b. 784 C. 786 d. 788
1. Find: a. Type of force needed to cut a huge box into three pieces of small boxes. b. Solve for the force needed to apply in each small box with the given stress. Stress (MPa) Length (cm) Width (cm) Height (cm) First Box 100 20 20 0.10 Second Box 120 20 16 0.04 Third Box 80 20 7 0.15
The specification of a cylindrical vessel are as follows: D = 350 mm t = 12 mm P = 4.5 MPa Determine the a) Longitudinal Stress; b) Transverse Stress ; and c) new diameter and wall thickness if the 550-mm length cylindrical vessel is replaced by a spherical vessel of the same volume and equal material strength.
Q2/ In the nucleus pulposus of an intervertebral disc, the compressive load is 1.5 times the externally applied load. In the annulus fibrosus, the compressive force is 0.5 times the external load. What are the compressive loads on the nucleus pulposus and annulus fibrosus of the L5-S1 intervertebral disc of a 90 kg man holding a 50 kg weight bar across his shoulders, given that 63% of body weight is distributed below the disc?
QUESTION 2 A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in diameter for the remaining 60mm. 2.1 The gradual application of a load P results in the link storing a total of 10J of energy, calculate the 2.1.1 magnitude of the applied load P; 2.1.2 value of the stress induced in each section3B 2.2.3total extension. 2.2 If this load had been applied suddenly but without shock, what instantaneous maximum stress would have been induced in the link? Let E=200GPA un