E The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of the thread on the pitch line as shown in the figure. The pitch (p) and included angle of the thread are 4 mm and 60°, respectively. The diameter of the best size wire is mm (round off to 2 decimal places). Pitch line Flank 60⁰ Wire 0.25p 1 -0.5p-

E The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of the thread on the pitch line as shown in the figure. The pitch (p) and included angle of the thread are 4 mm and 60°, respectively. The diameter of the best size wire is mm (round off to 2 decimal places). Pitch line Flank 60⁰ Wire 0.25p 1 -0.5p-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in
Please show the solution in number 4, if the final answer is 41.77 gpm.
Write the solution for the following: Member BC = -447.21 Member DF = -800 Member CE = 100
For an internal thread the outer diameter is 26 mm. The root diameter is 18 mm. Find the depth of thread (d) and pitch (P) of the Internal thread in mm. Depth of thread (d) Pitch (P) of the Internal thread in mm-
If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the Tape Length Find the Tape Length in mm=
A smooth plastic pipe is to be designed to carry 10 (ft^3)/s of water at 20°C (68°F) through 1750 ft of horizontal pipe with an exit pressure at 20 psig. The pressure drop is approximately -280 psig. Estimate the pipe diameter (in inches) that will result in the given pressure drop. For water at 68°F: p = 1.94 slug/(ft^3), and u = 2.09E-5 slug/(ft-s). Round your answer to 2 decimal places.
Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans: VB =-66.7 N 0.5 m 600 N 0.4 m B 0.2 m 0.2 0.6 m m 0.4 m 0.3 m
W2 Wi hi mm 122 Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown above (not drawn to scale). The bottom section has width w₁ = 25mm and height ₁ = 60mm. The top section has width w₂ = 70mm and height h₂ = 18mm. Enter your answer in millimetres correct to two decimal places.
6 solve 6 show complete STEP BY STEP solution, and draw a FBD.
66 0.60 in. 1.60 in. 0.40 in. -0.80 in.- → Shape of a slug for Problem 1-62. FIGURE P1-62
Find the following degree of freedom using the formula provided.
For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and y2 = 0.33 m. Find the moment of inertia about the horizontal axis where y=0 (bottom of the cross-section). Report your answer in units of m4 to four decimal places. y y2 x1 2 (no answer) Correct Answer: 0.002021