C.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In thyristor triggering, the pulse width should be long enough to permit holding current to be established

C.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In thyristor triggering, the pulse width should be long enough to permit holding current to be established

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8-The waveform of output voltage of half-controlled three phase bridge rectifier in each cycle contains: Two- pulse six- pulse three- pulse 9-The DC supply voltage of single phase bridge inverter is 300V. For quasi-square wave output voltage with a 60 percent ON time, the RMS value of output voltage is: 232.37V 220.5V 270.9V 10-For three phase bridge inverter with 120° conduction and resistive star-connected load, the waveforms of: (a) The load current and line voltage are quasi-square. (b) The load current is quasi-square and line voltage is a six- step. (c) The load current is six- step and line voltage is quasi-square. 9.
What is the difference between dc-dc switching mode regulators and PWM Inverters ?
4) Choppers is a a. AC - DC converters b. AC - AC converters c. DC - AC converters d. DC - DC converters 5) A single phase dc ac converter is also known as a. Rectifier b. Inverter c. Chopper d. Regulator
feedback and control system Explain How is the inverter type ACU open-loop systems calibrated
How you can obtain a single phase inverter with quasi square wave output voltage if you have only single phase inverters with square wave output voltage
Before firing, the voltage across the TRIAC is a. OV b. Once the TRIAC is turned on, it can only be turned off by. a. Removing gate voltage. b. Reducing the current flowing through TRAIC below the holding current value. Both a and b. Approximately Equal to power supply. C.
2-A) What's the name of the opamp circuit below? Briefly explain the logic. 2-B) Why is there a DC 1 volt offset in Vs sine signal?
In a full-wave rectifier _______________. a) the output is apure DC voltage. b) only the negative half of the input cycle is used. c) only the positive half of the input used. d) the complee input cycle is used.
Design Tri-state TTL gates, Explain the working mechanism? What is the use of Q diodes in a circuit?
Draw plc ladder diagram in digital gates circuit
Question 1 A single phase half bridge inverter feeds a resistive load R= 5N. If the source voltage is 60V. determine the (a) magnitude of output voltage (b) RMS value of fundamental component of output voltage (c) output power (d) voltage across the switches and (e) RMS and average value of current through the switch.
The circuit that converts ac to dc is called a. Attenuator b. Rectifier c. Inverter d. Amplifier