1. Maximum operating frequency of PIC microcontroller is 8 MHZ 12 MHZ 16 MHZ 20 MHZ 2. PIC 16f877a has type of ROM ROM PROM EPROM EEPROM 3. Maximum operating frequency of PIC microcontroller is 8 MHZ 12 MHZ 16 MHZ 20 MHZ 4. PIC 16F877A HAS TOTAL NUMBER OF PINS 28 40 42 33 5. What is the file extension is used to load in a microcontroller to execute an instruction? .doc .txt .hex 6. PIC16F877A as other PIC families is implemented using RISC approach, with only 33 instructions. • True • False 7. PIC is generally comes with a variety of families; PIC16 with (Mid-range) family True False

1. Maximum operating frequency of PIC microcontroller is 8 MHZ 12 MHZ 16 MHZ 20 MHZ 2. PIC 16f877a has type of ROM ROM PROM EPROM EEPROM 3. Maximum operating frequency of PIC microcontroller is 8 MHZ 12 MHZ 16 MHZ 20 MHZ 4. PIC 16F877A HAS TOTAL NUMBER OF PINS 28 40 42 33 5. What is the file extension is used to load in a microcontroller to execute an instruction? .doc .txt .hex 6. PIC16F877A as other PIC families is implemented using RISC approach, with only 33 instructions. • True • False 7. PIC is generally comes with a variety of families; PIC16 with (Mid-range) family True False

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Problem #4: Consider the Programmable Array Logic PAL module below '1' A B C D F₁ F2 F3 1. Determine the corresponding product term per row PRODUCT TERMS 000000
4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
2) Convert Hexa-decimal to Octal a. 7E6A(16)=?(8) b. C350(16)=?(8) c. 9E36.7A(16)=?(8) d. EADD.EBEF(16)-?(8)
Explain the function of Multiplexer and, Draw the 2 x 1 multiplexer logic circuit diagram and function table. How many selection inputs are required for a 4096 x 1 Multiplexer?
1. Letter A at the end of PIC16F877A means that this MCU is an -- 2. Technology approach for microcontroller is- 3. when type the body of the program, any program must contain some important lines, the fuses line will set the -------- in the PIC. 4. for simulating PIC response, We will use- 5. suppose that we need to display number 5 on a common cathode 7-seg then we must feed segments --------- with Vcc and segment -- with GND. program.
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
3. Draw the block diagram of an 8255 PPI chip and describe its different programming modes. Configure 8255 as follows: port A as output, B as input, and all the bits in port C as output. Determine the content of the Control Register and program the 8255 to get data from port B and send it to both port A and port C. (Assume the standard port addresses of 8255)
1)Write a program in 8051 to copy the contents of registers R0 to R7 into internal RAM addresses 40H to 47H respectively using PUSH instructions. Assume Register Bank 0 is selected. 2 )Designa Programmable timer using 8254 and 8086 to generate a square wave of period 5 millisecond. Interface 8254 at the address 0040H for Counter 0 and write the assembly language program. The 8086 and 8254 runs at 6 megahertz and 3 megahertz respectively.
P Flag question Explain the MUL instruction of 8086. Compare it with IMUL instruction. (1 +1 Marks) Write a Assembly language program for 8086 to find the cube of a number using MUL instruction. (5 Marks) (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) B I III
1- What does the VoH parameter of a logic IC refer to? a) The highest permissible output voltage. b) The lowest output voltage recognized as logic 1. c) The highest output voltage recognized as logic 1. d) The highest output voltage recognized as logic 0.
DIsassemble the following MIPS 32-bit hexadecimal instruction written as addr:instr 60005000 : 0c000020
A) List and describe 10 features of the Atmel ATmega 2560 AVR microcontroller (use the ATmega 2560 complete reference manual for help). B) List and describe two AVR instructions. As part of your description make sure that you list the operation for each instruction that is provided in the instruction set summary.