Identify the working substance, specify the kind of system and sketch the system boundary. PLEASE ANSWER it in 1hr. Identify the working substance, specify the kind of system and sketch the system boundaryExample:Nitrogen, at a pressure of 200 kPa and a temperature of 25°C, flows at a velocityof 20 m/s through a pipe with a diameter of 35-mm.Working Substance: NitrogenSystem: OpenNitrogen1. Liquid water enters a pump at 250C, 100 kPa and exits at a pressure of 5 MPa.Working Substance:System:Drawing:2. A compressor receives ambient air at 95 kPa, 200C, with a low velocity. At the compressor discharge,air exits at 1.14 kPa, 3800C, with a velocity of 110 m/sec.Working Substance:System:Drawing3. Steam enters a turbine at 3000C and is exhausted at 20 kPa.Working Substance:System:Drawing

Note: “Since you have asked multiple question, we will solve the first question for you. If you want…

Answered: 1. Liquid water enters a pump at 250C,…

Engineering

Mechanical Engineering

1. Liquid water enters a pump at 250C, 100 kPa and exits at a pressure of 5 MPa. Working Substance: System: Drawing:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

03: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (a) Find the velocity at the nozzle exit. (b) If the rate of flow of fluid is 31.6 kg/s and the specific volume at the inlet is 0.19 m'/kg, find the inlet area. (c) If the specific volume at the nozzle exit is 0.5 m/kg, find the exit area of the nozzle.
ull ll A:Y Drop in enthalpy of steam enters an engine at a pressure of 10 bar absolute and 400°C. It is exhausted at 0.2 bar. The steam at exhaust is 0.9 dry equals to: * 889.9 kJ/kg 998.8 kJ/kg 19889.9 kJ/kg 1889.9 kJ/kg Find the specific volume and internal energy of wet steam at 18 bar, dryness fraction 0.85. v= 0.0935 m3/kg, u= 2340.75 kJ/kg v= 0.0835 m3/kg, u= 2330.75 kJ/kg v= 0.0953 m3/kg, u= 2430.75 kJ/kg v= 0.0935 kg/m3, u= 2340.75 kg/kJ
... Moving to another question will save this response. Question 7 Compressed air with a flowrate of 8 kg/min flows through a two-stage turbine and heat exchanger system as follows: • At the entrance to the system (point 1), the pressure of the air is 8 bar and the temperature of the air is 359 K. • From 1-2 the air passes through a heat exchanger which increases its temperature to 922 K. • From 2-3 the air passes through a turbine, with a pressure ratio of 3 (i.e. P₂/p₂=3). This first turbine has an isentropic efficiency of 65%. • From 3-4 the air passes through a second heat exchanger, which increases its temperature back up to 922 K. • From 4-5 the air passes through a second turbine with a pressure ratio of 3 and an isentropic efficiency of 80%. The properties of air are: cp = 1.005 kJ/kgk, cv = 0.718 kJ/kgK, R = 0.287 kJ/kgK, and y= 1.4. Select the correct value for each of the following values: ₂) a. The heat transfer to the air in the first heat exchanger (i.e. ₁) i in kW: b.…
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar what is the pressure in bar at state 4 to 3 decimal places? what is the specific entropy in kJ/kg-K for state 5 to 4 d.p.?
Q4: Why the stroke length of the racing cars' engines is always smaller than its bore diameter?
Pls. Answer thank you! A cooling tower has an efficiency of 65%. Water enters the tower at 55°C. The wet bulb temperature of surrounding air is 27°C. What is the temperature of water leaving the tower?
1. Two kilograms of air at a pressure of 2.25 MPa and temperature of 27C is heated atconstant volume to a final pressure of 2.5 MPa. Compute for the:a. Change in internal energyb. Change in enthalpyc. Change in entropyd. Heat transferrede. Non-flow work 2. In a constant pressure process, 325 KJ of heat are added to 6.55 kg of ideal gas(R=208 J/kg-K and k = 1.65) initially at 290 K. Calculate:a. Final Temperatureb. Change in enthalpyc. Change in internal energyd. Change in entropye. Non-flow work
FLUID MECH Support your answer with the appropriate solution and diagram. 5. Air at 2.50 kg/m^3 enters a nozzle that has an inlet to exit ratio of 2:1 with a velocity of 120 m/s and leaves with a velocity of 330 m/s. Determine the density of air in kg/m^3 at the exit. A. 1.02 B. 1.82 C. 2.78 D. 4.02
Note: Show all your solutions in separate sheets as required. Indicate all of your answers on this page in the provided blank lines. 1. Using the Steam Tables, find and entropy of steam at the inlet and outlet of a boiler and heat added when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at boiler inlet), is superheated to 100 deg C SH at the same pressure. Total flow volume rate of steam = 0.5 cu.m per sec. Indicate units.
For a certain gas with constant, R = 320 J/(kg-K) and constant volume specific heat, Cv = 184 J/(kg-K), what is the value of constant pressure specific heat, Cp if the system undergoes a reversible non flow constant pressure
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. find Wnet, Ec, Ee and the ideal steam rate. Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. PLEASE USE THE STEAM TABLE PROVIDED: https://drive.google.com/drive/folders/15t3WMv7xSTHmwXWXp0X2ZV6aYWhXuRCS?usp=sharing
1. A horizontal "hot air blower" consists of a fan, an electrical heating element and a nozzleThe power input to the fan is 50 J/s and the power input to the heating element is 1.44 kJ/s. The air enters the fan with negligible velocity at a pressure of 1 bar and a temperature of 20 C, the volumetric flow rate being 0.5 m3/min. After passing over the heating element, the air leaves the nozzle with a velocity of 25 m/s and a pressure of 1.1 bar. Treating the complete arrangement as a steady flow system and ignoring any heat loss from the system, determine: (a) The mass flow rate of air entering the fan in kg per second(b) The kinetic energy of the air leaving the nozzle per second(c) The change in enthalpy of the air occurring per second between entering the fan and leaving the nozzle(d) The temperature of the air as it leaves the nozzle.(e) The density of the air as it leaves the nozzle(f) The flow area at the nozzle exit.Take R = 0.287 kJ/kgK and cp = 1.005 kJ/kgK