You have an adiabatic steam turbine. The steam enters a 0.1m diameter pipe at 200 m/s and it at state conditions of 773K and specific volume of 0.0482 m/kg. When it exits the turbine as a saturated mixture at 393K its specific volume is 0.665 m/kg. Using the first law for control volumes, find the work output of the turbine. You can neglect the change in KE and PE.

You have an adiabatic steam turbine. The steam enters a 0.1m diameter pipe at 200 m/s and it at state conditions of 773K and specific volume of 0.0482 m/kg. When it exits the turbine as a saturated mixture at 393K its specific volume is 0.665 m/kg. Using the first law for control volumes, find the work output of the turbine. You can neglect the change in KE and PE.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Helium is compressed through a compressor steadily. At the inlet the pressure is and the temperature is . At the exit the pressure is and the temperature is . The power input is and the heat loss rate is during this process. Neglect the kinetic and potential energy changes. Assume helium is ideal gas with a constant specific heat and its specific heat ratio , which means that enthalpy can be calculated using . Select the simplified the energy balance equation for this process_________ A. B. C. D.
Q6) One kg of air is allowed to expand reversibly in a cylinder behind a piston in an isothermal process at 260°C, while the volume is doubled. The piston is then moved and heat rejected at constant pressure until the volume is the same as it was initially. Find the heat flow and the overall change of entropy.
2.Steam enters an adiabatic turbine at 3MPa and 500C and exits at 30 kPa. If the efficiency of the turbine is 92%, find the actual and isentropic temperatures, and the change in specific volume across the turbine.
During the execution of a reversible nonflow process, the work is 216 kJ. If the initial pressure and volume 600 kPa and 0.1 m3respectively and the pressure varies as p = -300V + 630 kPa where V in m3, find the final volume and final pressure
Inside the cylinder piston system shown in the figure, there is 0.2 kg of air at 400 kPa pressure and 30 ° C temperature. The piston is attached with a pin. The system comes to balance after the pin is pulled. The cylinder piston system is completely adiabatic. The ambient pressure is 120 kPa and the temperature is 20 ° C. Find the net entropy change, the work done during the process. Keep specific temperatures constant.
Find the magnitude of the work for the process ,ASAP in 20min i will upvote
One way to determine the quality of saturated steam is to throttle the steam to a low enough pressure that it exists as a superheated vapor. Saturated steam at 500 kPa is throttled to 0.1 MPa, 100°C. Determine the quality of the steam at 400 kPa side. (Starts the calculation from mass and energy conservation)
steam at 3.5 MPa with a quality of 89%, enters an adiabatic diffuser with velocity of 30.5 m/s and leaves at a lo of 4 m/s and 0.2 MPa. Find all the possible exit properties of this steam. Assume: Adiabatic, steady-flow system and neglect the potential energies and work.
Helium is compressed through a compressor steadily. At the inlet the pressure is and the temperature is . At the exit the pressure is and the temperature is . The power input is and the heat loss rate is during this process. Neglect the kinetic and potential energy changes. Assume helium is ideal gas with a constant specific heat and its specific heat ratio , which means that enthalpy can be calculated using . Calculate the work per unit mass _________
40°C 4. A mixing chamber receives 5 kg/min of ammonia as saturated liquid at -20°C from one line (1) and ammonia at 40°C, 250 kPa from another line (2). The chamber also receives 325 kJ/min of energy as heat transferred from a 40°C reservoir as shown in figure. At the outlet, ammonia leaves as saturated vapor at -20°C. Find the mass flow rate in second line and calculate the total entropy generation in the process. Is this process possible?
A turbine operating in a continuous flow works adiabatically. The water vapor enters the turbine at a temperature of 650 C and comes out with 20 kPa pressure and 85% dryness. Find the mass flow rate (kg / sec) required to generate 10 MW of power from the system (ignore KE and PE changes)
I need the answer as soon as possible