1. If the velocity of point B is 50 m/s to the right at the instant shown, find the angular velocity of bars AB, BC. and CD. NOT TO SCALE 24 m 16 m - 20 m Used with permission from "Engineering Mechanics: Dynamics." McGil/King, 4th Ed. 2003 WAB- -0.32 k rad / sec: Wnc-3.13 k rad / sec WeD--0.48 k rad / see O WA -3.13 k rad / sec: W nc 3.13 k rad / sec: Wep= -0.48 k rad / sec O AB" -3.13 k rad / sec: WuC0k rad / sec; Wen- -2.08 k rad / sec None of the above B.

1. If the velocity of point B is 50 m/s to the right at the instant shown, find the angular velocity of bars AB, BC. and CD. NOT TO SCALE 24 m 16 m - 20 m Used with permission from "Engineering Mechanics: Dynamics." McGil/King, 4th Ed. 2003 WAB- -0.32 k rad / sec: Wnc-3.13 k rad / sec WeD--0.48 k rad / see O WA -3.13 k rad / sec: W nc 3.13 k rad / sec: Wep= -0.48 k rad / sec O AB" -3.13 k rad / sec: WuC0k rad / sec; Wen- -2.08 k rad / sec None of the above B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P₁₂ = ? 250mm 2 56 300mm P₁= 80 kPa Fx=? of Fy=?
C 5.8 m 3.2 m 1 hi 12 3,5 m %3D h2 4.5 m h2 L203X152X25.4 Shape Steel A992 Gr. 50 Gage of Angles 75 mm g1 T 75 mm g2 Bolt h 28 mm Bolt Diameter, dbolt 50 mm A aspace 65 mm b,pace d. 90 mm Сэрасе 70 mm 12 dapace 90 mm espace 95 mm fapace I || |||
75 mun 500mm 75-22mm 75mm 200mm 75mm →4-20mm Ø 75mm 300mm fé=21 MPa 200mm fy= 276 MPa Cg? Cp = ?
Situation 6: AC3x35 has a length of 1.40 m. Fy-248 MPa. The properties are given below. Properties of C - Channel with L-1.40 meters. A-703 mm^2 d = 76 mm bf - 34.8 mm tf-6.93 mm kdes - 17.5 mm tw - 3.35 mm rx - 30.5 mm ry - 10.0 mm Cw-0.0741 x 10^9 mm 6 ro 39.90 mm H-0.646 J-9.41 x 10^3 mm 4 1. Which of the following most nearly gives the axial capacity (Pu) considering Flexural Buckling if support conditions are both are pinned? 56 KN O 48 KN O 77 KN O 65 KN
Question 39/50 Situation 39, 40 10 m/s Es=200 GPa E,=105 GPa 50kg Steel 15 mm-diaBrass k=25 kN/mm 1.5m 1.5m 0.5m O Zoom image Determine the stiffness of Spring, Steel and Brass assembly as shown. 8256.25 N/mm 9141.75 N/mm 2563.23 N/mm O5632.20 N/mm Previous Next
A cantilevered beam AB carrying a uniform load, w as shown in Figure Q2 (c). The cross section of the beam are shown in Figure Q2 (d). If the allowable bending stress is 8.5 MPa and the allowable shear stress is 0.8 MPa, determine the maximum permissible value of the load P. W
dy Find when v5x tan (/5x). V dx dy d.x
A machine component is subjected to the forces and couples shown. The component is to be held in place by a single bolt that can resist a force but not a couple. Determine the distance of the bolt hole from point G if it is to be located on line FG. 125 N 15° 200 N E 50 mm 42 N-m 520 mm 240 mm 50 mm D 70° 40 N-m 640 mm H C 80 N 20 N 180 mm B 50 mm
Gate ACB is in a shape of a sector of a circle whose radius is 6m as shown. Determine the following: a) Horizontal component FH is Blank 1 KN b) Vertical component Fv is Blank 2 KN c) Distance of FH from point "C" is Blank 3 m c) Distance of Fv from point "C" is Blank 4 m
2. Design the anchored sheet pile wall supporting a loose sand fill as shown in the following Figure. GWT is at the same height on both sides, and assume yw=10kN/m³. Based on the log spiral solutions, the K₂ for the loose sand is 0.3 while the K₂ and Kp for the dense sand are 0.2 and 13.125, respectively. Using the free earth support method, do the following: a) For a factor of safety of 2 on the passive resistance, determine the required depth of penetration depth, D. (initial trial with D'=1.5m) b) Determine the bending moment and the anchor load. c) Select a sheet pile section from the Table 9.1 (E-210x10³ MN/m² and fa-210 MN/m²) D U 7.0m. ↓ ↓ Yt = 16.5 kN/m³ $' = 30° Loose sand fill: Yt = 19.5 kN/m3 $' = 30° Dense sand: Yt = 21 kN/m³ $' = 40° q=10 kN/m² 1.5m. 0.5m.
Situation 7: A C5x9 has a length of 1.40 m. Fy= 248 MPa. The properties are given below. Properties of C - Channel with L = 1.80 meters. A = 1700 mm^2 d = 127 mm bf 48.0 mm tf = 8.13 mm kdes 19.1 mm tw = 8.26 mm rx = 46.7 mm ry = 12.3 mm Cw = 0.787 x 10^9 mm^6 ro = 53.3 mm H = 0.815 J = 45.4 x 10^3 mm^4 1. Which of the following most nearly gives the axial capacity (Pu) considering Flexural Buckling if support conditions are both fixed? O 287 KN O 266 KN. O 299 KN O 222 KN
A steel bar shown is made up of two segments. Determine the displacement of A relative to fixed support D.