1. Effective width of the flange for the interior beam 2. Ultimate maximum allowable moment 3. Allowable ultimate load P for the given beam if service uniform load for dead load is W = 20 kN/ m. Neglect beam weight. fy = 415 MPa, f'c = 21 MPa, As = 5- 28 mm Ø bf 90 mm 3 m 475 mm 550 mm "2:50 m 250 mm 1.5 m 1.5 m

1. Effective width of the flange for the interior beam 2. Ultimate maximum allowable moment 3. Allowable ultimate load P for the given beam if service uniform load for dead load is W = 20 kN/ m. Neglect beam weight. fy = 415 MPa, f'c = 21 MPa, As = 5- 28 mm Ø bf 90 mm 3 m 475 mm 550 mm "2:50 m 250 mm 1.5 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the safe live load that the T-beam section shown can carry if it has a simple span of 5.8m. The beam is reinforced with 4-025mm placed in two layers. Use f'c = 21MPA, fy = 414Mpa. -800mm t=50mm d=300mm 2-025mm cover=65mm 2-025mm
B2
The propped beam is 10m long and is required to carry a load of 250kN as shown. If the yield stress steel is 248MPa, determine the plastic moment capacity of the beam if a load factor against failure is 1.2 Pu 3 7 THOUGH
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
Question 2: A compression member is subjected to service load of DL-180 KN and LL-335KN. The member is 6 m long and fixed at A and pinned at B. Use 992M steel F, = 345 N/mm² Select W shape, make two complete attempts. 6m B A
The frame shown below is subjected to uniformly distributed load of 2.6KP.. Determine the maximum moment of member BF (assume simple beam support) A E, 1.5m F 1.5m 351 C 1.5m H 3m B
Please explain all options..
AW460×60 steel beam is loaded as shown. Assume w - 50 kN/m, Mo - 95 kN-m, Las - 3.8 m, Lec - 1.6 m, E- 200 GPa, and I- 255 x 10° mm. (a) Determine the reaction force at roller B. Forces are positive upwards. (b) Determine the maximum positive bending moment in the span. (c) If the allowable bending stress is 210 MPa, determine the minimum acceptable section modulus for the steel beam. Mo LAB LBC Answer: (a) Ву - kN (b) Mpos kN-m (c) Smin x 10° m3
Question 6: Determine the LRFD design compressive strength for the shown built-up compression member composed of 2 channel (MC) sections welded to a plate. The effective buckling length of the member (KL=21 ft 2 in). Use steel with F, = 42 ksi. PL를X 12 KL = 21 A 2 in F, = 42 ksi Hint: Use parallel axis theorem to find moment of inertia about x and y axis. MC 13 x 50
F- 3 kN 500 mm P = 2.8 kN y Figure Q1 400 mm A z Figure Q1 shows one 'L’shaped beam ACD which is built -in at one end. It is loaded with load F=2.5kN at its free end D and with load P= 3.5kN at point C. The beam has solid round cross-section with diameter of 100 mm. The beam is made of steel with E= 200 GPa and v= 0.3. Use point B as the critical point to be analysed a) Calculate the respective stresses values and draw the stress element at point B in the x-y direction. b) Calculate and draw the principal stress element & maximum shear stress element. c) If a strain gauge is fixed at point B at -20 degrees from the x-direction, calculate its value.