Assignment No. 01 A simply supported deep beam has a clear span equal to 3660 mm, a total height equal to 1830 mm, and a width of 460 mm. The beam supports an 460 mm.-square column at midspan carrying a dead load equal to 1335KN, and a live load equal to 1068KN. Column: 460mmx460mm DL=1335 kN LL= 1068 kN 1830 mm Design the beam using the strut-and-tie model, using fc equal to 28MPA and fy equal to 420 MPa. 1830 mm 1830 mm Column: 460mmx 460mm Column: 460mmx460mm

Assignment No. 01 A simply supported deep beam has a clear span equal to 3660 mm, a total height equal to 1830 mm, and a width of 460 mm. The beam supports an 460 mm.-square column at midspan carrying a dead load equal to 1335KN, and a live load equal to 1068KN. Column: 460mmx460mm DL=1335 kN LL= 1068 kN 1830 mm Design the beam using the strut-and-tie model, using fc equal to 28MPA and fy equal to 420 MPa. 1830 mm 1830 mm Column: 460mmx 460mm Column: 460mmx460mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Someone can help me with this one please
A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of610.5mm. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads ofWd = 13.5kN/m and WL = 35.5kN/m. f'c = 28Mpa and fy=420 MPa Given: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam.
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
5.14-2 Design a bearing plate of A36 steel to support a beam reaction consisting of 28 kips dead load and 56 kips live load. Assume that the bearing plate will rest on concrete with a surface area larger than the bearing area by an amount equal to 1 inch of concrete on all sides of the plate. The beam is a W30 X 99 with F, = 50 ksi, and the concrete streng th is f. = 3 ksi. a. Use LRFD. b. Use ASD.
Find the value of internal force member and state if it is in Tension or Compression
AW460×60 steel beam is loaded as shown. Assume w - 50 kN/m, Mo - 95 kN-m, Las - 3.8 m, Lec - 1.6 m, E- 200 GPa, and I- 255 x 10° mm. (a) Determine the reaction force at roller B. Forces are positive upwards. (b) Determine the maximum positive bending moment in the span. (c) If the allowable bending stress is 210 MPa, determine the minimum acceptable section modulus for the steel beam. Mo LAB LBC Answer: (a) Ву - kN (b) Mpos kN-m (c) Smin x 10° m3
Question 6: Determine the LRFD design compressive strength for the shown built-up compression member composed of 2 channel (MC) sections welded to a plate. The effective buckling length of the member (KL=21 ft 2 in). Use steel with F, = 42 ksi. PL를X 12 KL = 21 A 2 in F, = 42 ksi Hint: Use parallel axis theorem to find moment of inertia about x and y axis. MC 13 x 50
please help
Situation 2. A W14x90 of A992 steel is used as a pin-connected column. The 30ft long column is braced at mid-height with respect to its weak axis. Determine the axial compressive load. (ASD & LRFD) 30ft Properties of W14x90: 15ft 15ft A = 26.5 in.² d = 14.0 in. by = 14.5 in. t₁ = 0.710 in. tw = 0.440 in. Tx = 6.14 in. ry = 3.70 in. by/2t, = 10.2 h/tw = 25.9
Hw Draw S.f,B.M and elasticdiagvams for the beam shown beloi by using method of equations? 4 KN Im Im 4m 2m
AW 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm? , = 862 x10 mm d = 549 mm 4 = 38.7 x10 mm tw = 14.7 mm bị = 214 mm t, = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75KN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015