Answered: 1. Calculate the voltage output by the…

1. Calculate the voltage output by the secondary winding of a transformer if the primary voltage is 180v, the secondary winding has 390 turns, and the primary winding has 15100 turns.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Related questions

Q: Consider a simple pendulum (mass m, length l) whose point of support is forced by some external mech...

A: Solution- On the horizontal axis- x=Rcosθ+lsinϕ put θ=ωt,x=Rcosωt+lsinϕ ......................

Q: Mr. Wahid needs to transmit a digital signal (data) to Mr. Alice through internet. Mr. Wahid has con...

A: Phase shift key: It is the digital modulating technique that carries the data by changing the phase.

Q: takes 30 A at 200 V the power input being 1,500 W. On open circuit, both transformers give a seconda...

Q: Consider the following AC bridge circuit. Calculate the resistance R1 that will cause this bridge. i...

A: This question belongs to measurements and instrumentation . It is based on the concept of balanced b...

Q: a. What is the counting range in binary and decimal for an up-counter with 3 bits? p. What is the co...

Q: Write the equation for V

A: Given,

Q: R = 5.0 2 %3D R 12.0 2 R 30.0 2 R 6.0 2 R6.0 m

Q: Find the transfer function x2/F and x1F. Where, K= 2, K2=2 , K3= 1+c fv1=1/2, fv2= 2+b, fv3= 3 ...

Q: Define voltage regulation

Q: :Find the values of VA, VB, Vo in the circuit, also determine I, I1, I2, load voltage, and load powe...

Q: A 6 pole induction motor is supplied from a 400 V, three phase, 50 Hz supply system. The frequency o...

Q: Derive the Rs formula from the voltage divider formula. Show your steps. Given that the internal res...

Q: a power factor of 0.45 lagging?

A: Since you have asked multiple question ,we will slove the first question for you .If you want any sp...

Q: About sources, check the correct statement(s). a) A power supply is composed of at least six parts,...

Q: At a 115kV substation the PT raatio is 1000:1 and CT ratio is 1,200:5. The potential going into the ...

Q: a. What is the mechanism for the occurrence of Self Potential (SP)? b. What are the applications of ...

A: Self Potential (SP) is a geophysical formulation based on the proportion of automatic or natural ene...

Q: Determine the critical frequencies associated with low frequency response in the circuit given below...

Q: Problem 1 For the circuit shown, use nodal analysis to determine the values of the voltages Va and V...

A: This question belongs to circuit theory . It is based on the concept of nodal analysis in the circui...

Q: A 60-MVA, 69.3 kV, 3-phase synchronous generator has a synchronous reactance of 15 ohms per phase an...

A: Do all the calculation in per phase .

Q: Use Kirchhoff's Laws to find the branch currents indicated in the following networks: Show complete ...

Q: Continuous-tim Assignment 1 :Find the Close loop Transfer function of a given system using Matlab. R...

Q: The switch in the circuit has been in position a for a long time before it moves to position b at t ...

Q: Calculate the Fourier transform of the 'off-on-off' pulse f(t) defined by

Q: V3 + iz 50 Ω 30 N 202 + 45 N 100 V 0,2v3 5i2 0,02v1

Q: Describe two methods of controlling voltage in a power system.

A: You have asked multiple independent questions. We are authorized to answer one question at a time. S...

Q: IA 5ix ziy V8 VA Ix VGND Using Nodal Analysis, Find the values of the voltoges VA, VB, and V t.

Q: QI: Determine the proper values of load resistance R1, and maximum Zener current Iz, to maintain the...

Q: Draw a suitable circuit, which has the following Maxwell s loop equations. 121,-412-313=10 -41,+1412...

Q: Find the Transfer Function Y(s)/X(s) of the following network. H3 H2 L2 L1 G3 G4 Y(s) Gg. Y(S) R(s) ...

Q: Q1: Find F.T for the signal shown below:

A: The given signal is shown below:

Q: Find the Boolean functions Y (at the Out node) for the following PTL circuit. Vdd A В- Out

A: The Pass transistor logic(PTL) circuit diagram is shown below,

Q: angular waveguide has a dimension of 3cm by 2 cm is used

Q: w[n] Sys, { } Sys,{ } (a) Let the input-output relationsh

Q: If f(t) F(w) , find the fourier transform of : t*(df/dt)

A: Step 1 Fourier transform: This is used to convert the time domain signal into a series of sinusoidal...

Q: (a) Given Ē = rsin(0)sin(4) a, + rcos(0) cos(4) ag – rcos(4)a V/m, compute the total energy stored b...

A: GIVEN: E→=r sin(θ) sin(ϕ) ar→ + r cos(θ) cos(ϕ) aθ→ - r cos(ϕ) aϕ→ V/m FIND: Total energy stored by ...

Q: 14. What is the resonant frequency of a circuit having a resistance of 2 000 ohms, inductance of 0.0...

Q: From the oscilloscope screen image, if the Time/Div button is set to 20 ms/div, which of the followi...

Q: The resistance of a wire is 140.32 ohms at 100 °C and 115 ohms at 45 °C. Determine the temperature c...

Q: A 60-MVA, 69.3 kV, 3-phase synchronous generator has a synchronous reactance of 15 ohms per phase an...

Q: Answer the follwing. Modified true or false. Write True if the statement is true. If not, write fals...

Q: (c) Determine with justification whether each of the following functions R →R is one-to-one, onto or...

A: The solution is given below

Q: 7-24 It is desired to multiply the frequency and deviation of an FM signal by a factor of 864. Using...

A: The solution is given below

Q: a) Calculate the intrinsic carrier concentration in silicon at (i) T = 250 K and (ii) T = 350 K. (b)...

A: a) i) Intrinsic carrier concentration ni for semiconductor material is given as, ni=BT32e-Eg2KT ...

Q: 4)Mark the correct statements: a) The frequency at the output of a half-wave rectifier circuit is 3...

Q: Find the current i for all t.

Q: - The independent current source in the circuit generates zero current for t 0. 100 mH a) Sketch th...

A: we have given; in circuit the independent current source genrates 0 current where pulse 10te-5tAfor ...

Q: 2. Consider an input x[n] and a unit impulse response h[n] given by x[n] = )"-2 u[n – 2] h[n]= u [n+...

A: This question belongs to signal and system . It is based on the concept of z transform of the system...

Q: Discuss different design of aspects of PEV, BEV and HEV with suitable diagrams?

A: The standard electric car (EV), also known as a battery-powered electric vehicle (BEV), the hybrid e...

Q: (b) Given the following logical circuit with three inputs A, B and C': i. Use the boolean algebra no...

A: Use basic laws of Boolean algebra.

Q: www R RS Z: Z1 5. The figure attached shows AC Maxwell Induction Bridge, Ls with R1=1002, Lı=250mH, ...

Concept explainers

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.

Question

Answer the following with illustration and solutions.

1. Calculate the voltage output by the secondary winding of a
transformer if the primary voltage is 180v, the secondary
winding has 390 turns, and the primary winding has
15100 turns.
2. Calculate the load current L and load voltage UL in this
transformer circuit and determine its type of transformer.
3690
1200
19 VAC
3kN
turns
turns

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
An ideal transformer has no real or reactive power loss. (a) True (b) False
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
Seconday winding of transformer is made-up of material. O insulated CRGO conductor O insulated copper conductor O Cold Rolled Grain Oriented (CRGO) conductor Cold Rolled Grain Oriented (CRGO) Silicon Steel
opper losses Which of following is a variable loss in a transformer? O Constant loss O Eddy current Hysteresis losses O Copper loss
How do i calculate secondary current in transformer analysis