1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole centrally located. If the allowable tensile stress for the steel is 38 ksi, calculate the tensile load that may be applied to the bar.

Q: 1. Calculate the stress developed (in Pa) for the following structural members that are each…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: ild steel rod having a stress of 50 Mpa and having a diameter of 20 mm  What is the force applied

A: Given:Stress, σ=50 MPadiameter, d=20 mm

Q: How would you predict if a column will fail in buckling or in compr

A: Buskling is the sudden lateral deformation or deflection of the column or beam. It happens when the…

Q: ort square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000…

A:

Q: Solve the following problem of a steel tensile plate with a concentrated load applied at the top, as…

A:

Q: (a) What pressure can the cylinder carry if the permissible tangential stress is psi and the theory…

A:

Q: A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress…

A:

Q: walled vessels is assumed to apply? ssure found in part (a), compute the s

A:

Q: Consider a tetrahedron containing point Q and show the forces on the faces of the  tetrahedron due…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a subjected to an internal pressure of…

A: Givendia=400mmthickness t=20mmInternal pressure P=4.5MN/m2

Q: A bar is applied a tensile load of 50 kN having diameter 10 mm,  Calculate the tensile stress induc

A: Given:force, F=50 kNdiameter, d=10 mm

Q: An aluminum rod length of 1.0 m and cross-secrional area 0.0005 m2 is used to support a load of…

A: Calculated stress on the aluminum rod. length of 1.0 m and cross-secrional area 0.0005 m2 is used to…

Q: In Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data: The diameter of part AB is dAB=100 mm The diameter of part BC is dBC=80 mm The length of…

Q: 4. The cross sectional area of each member of the truss is 1.6 in?. Calculate the stresses in…

A: GIVEN DATA - A PLANE TRUSS GIVEN WITH AREA 1.6in2 WE HAVE TO FIND STRESS IN GIVEN MEMBER

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

A:

Q: A long, flat steel bar 260mm wide and 35mm thick has a circular hole 50mm in diameter, centrally…

A:

Q: A cylindrical rod .5" in diameter is subjected to an axial load of 11,300 lbs. A square bar of .5"…

A:

Q: WITH DESCRIPTION AND STEPS APPLIED, TO HELP ME UNDERSTAND APPROPRIATELY

A: Hoop stressExplanation:Step 1:Step 2: Step 3: Step 4:

Q: 4. Before the 400-kN load is applied, the rigid each of cross-sectional area 1400 mm2, as shown in…

A:

Q: A steel rod 8 mm in diameter is under the action of a tensile force (P) of 600 Newton. Calculate the…

A: Tensile stress is given by the following formula, Sigma=P/A Where P is the tension force and A is…

Q: 2. A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjected to a…

A: Given: Thickness of the steel bar is 0.5 in. Width of the steel bar is 1.5 in. Length of the steel…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

A:

Q: A In Figure 2, different square cross-section bar with dimensions, loading condition and material…

A:

Q: 2 A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN.…

A:

Q: ADISIDO diameter is 10 times the tube thickness, find the thickness (mm) of the tube.

A: Given   Load, P = 500 kN     Stress = 140 MPa Find   Thickness, t

Q: 1. A hollow steel tube of external diameter 100mm and a wall thickness 12mm is subjected to an axial…

A:

Q: A steel bar having cross sectional area of 100 n mm² is subjected to a tensile force of 40 kN.…

A: It is given that, the bar is subjected to a tensile force of  Cross-sectional area of the bar is It…

Q: 4) A sophisticated machinery design has a flat bar fillet component with a thickness of 10mm. For an…

A:

Q: The figure below shows the stress-strain behavior of a mild steel (the insert shows part of the same…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

A:

Q: The structure shown below carries a load of 20 kN. Determine the required diameters of rods AE and…

A:

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.