Answered: 1. A hydraulic press has a ram of 30 cm…

1. A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight lifted by the hydraulic press when the force applied at the plunger is 500 N.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 4. The end of a semi-circular water trough is closed by a massless rectangular gate, shown below. If…

A: Given data Water depth = 3ft L = 3.5 ft Find the mass of counterweight in slugs and reactions at…

Q: Problem 4.4 A body of dimensions 1.5 m x 1.0 mx 2 m, weighs 1962 N in water. Find its weight in air.…

A: Given:dimesion of body=1.5 m×1.0 m×2 mweight of body in water=1962 NFind,weight in air?specific…

Q: - and H: Lonal body f er each of the - is filled wi

A: given:length of tank L=75cmwidth W=36cmheight H=30cm

Q: A cargo truck with a weight of 289 kN was raised using a hydraulic press. If oil acts on a piston…

A: Correct answer: 1148.62 kPa

Q: garage lift has a 52 cm diameter piston supporting the load. Compressed air with a maximum pressure…

Q: press , when the force (F) applied at the . plunger is 150O N

Q: A hydraulic lift uses an incompressible fluid to lift a 15 KN car. If the large cylinder's area is…

A: Given:- Weight of the car (W) = 15 kN Area : A = 25 × a A/a = 25 To Find :- Minimum force (F)…

Q: The hydrostatic pressure in a 24" diameter ductile iron water main is 75 p.s.i. If the thickness of…

A: The hydrostatic pressure is .The diameter of pipe is .The thickness of pipe is .

Q: A storage vat has vertical ends 3.6 m apart, of which one end is shown below. Oil (s=0.84) is stored…

Q: Two masses are fixed at 79 degrees to each other on a rotating disc, one is 3.2 kg at a radius of…

A: This question is based on the concept of balancing.

Q: Q.4 A hydraulic press has a ram of 20 cm diameter and a plunger of 5 cm diameter. The weight (in KN)…

A: Data given- DRam = 20 cm Dplunger = 5 cm W = ? Fplunger = 700 N

Q: A vertical bulkhead divides a tank 9m wide. On one side of the bulkhead there is fresh water to a…

Q: A vertical bulkhead is 2 metres wide and 3.7 metres high. It has fresh water on one side to a depth…

A: Draw sketch of door with forces on it

Q: A closed cylinder of diameter 30 cm and height of 20 cm is completely filled with water. Calculate…

Q: 2. A cylindrical container having cross-section area 100.0 m², which is put on the ground, is filled…

A: The unit of speed is “m/s” not “m/s2”. So in this solution unit of speed taken as “m/s”. Given data:

Q: A hydraulic press has a ram of 26 cm diameter and plunger of 6.5 cm diameter. How much weight can be…

A: According To Pascals Law, Pressure intensity at a point in any point is equal in any direction i.e,…

Q: Consider gate ABC (one piece square) and having a hinge at B, point on which can rotate. a) Draw the…

A: The resultant force created by the pressure of a liquid acting on submerged objects is known as…

Q: An effort of 2 kN is required just to move a certain body up an inclined plane of angle 15°, the…

Q: Explain with the aid of diagram the action of hydraulic press The following data pertains to a…

Q: A man is standing on a board on a frozen lake where there is no friction between the board and the…

Q: Find the acceleration of an open cylinder with 5 m diameter and holding - 6 m of water if the force…

A: Calculate the volume of water containing in the cylinder. V=π4d2h=π45 m26 m=117.81 m3

Q: A hydraulic press has a plunger diameter 4.5 cm. The force acting on the ram and plunger are 22.22…

A: As we know that pascals law is valid for this problem.

Q: A 1.2 m x 1.2 m square gate located in the vertical side of an open tank is pivoted about the…

A: To Find : The magnitude of hydrostatic force acting on the square gate.Given : The dimension of…

Q: A tank, shaped like a cone has height 8 meters and base radius 3 meters long. It is placed so that…

A: The height of cone is The radius of base is The density of water is

Q: The client is procuring a new hydraulic lifting jack. The jack is rated to lift 2000kg. Given that…

A: Solution: Given Data: m=2000 kgdp=25 mmdl=40 mm To Find: a) The force needed on the pumping piston…

Q: Calculate the force acting on a 30-cm diameter porthole of a ship if the center of the porthole is…

A: Given that: d = diameter of the porthole = 30 cm h = depth of center of the porthole from water…

Q: PROBLEM 3 GIVEN THE FIGURE. SOLVE FOR 4 m Hinge THE MAGNITUDE OF THE WL Gate REULTANT FORCE DUE TO…

Q: 3. An 8 ft diameter cylinder weights 500 lb and rests on the bottom of a tank that is 3 ft long.…

A: Given:To find:(a) Magnitude of the horizontal forces pushing on the tank. Net horizontal force.(b)…

Q: meter 30 cm and height o

Q: can i know for subpart c, why the value of the pressure inside is 150101.3 kPa? as the question is…

A: The net force in the door would be due to pressure difference at outside and inside of the door and…

Q: If the surface tension of the drop be 42.27x103 N/m, find the pressure difference of the drop

Q: A piston consist of two cylinder of different diameters (5 and 30 ) cm that connect together and…

A: Given data:

Q: hat can be lifted if the output piston has a diameter of 1 foot? Assume 80% efficiency of the…

A: P1 = P0 + ρ gd+ F1A1P2 = P0 + ρ g d + F2A2 P1 = P2F2A2 = ρ g d + F1A1

Q: Water 0,9 m R = 0,75 m 0,75 m K Water F 1,5 m 2m

Q: Weighted piston type accumulator is shown in the figure below. If area=340 cm², a lift of the ram…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

1. A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight lifted by the
hydraulic press when the force applied at the plunger is 500 N.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q4. A 50 cm steel rod (cylinder) used for reinforced concrete has a radius of 0.46 cm and it has a weight of 4.2 N. Calculate: a. the mass of the rod b. the density of the rod
Can you guys help me please
A water tank, 7 m diameter, is made from steel plates that are 12.5 mm thick. Find the maximum height to which the tank may be filled if the circumferential stressis limited to 42 N/mm?. The specific weight of water is 9.81 kN/m³.
Solve it right away systematically. SHOW FBD. Clear and complete solution please thank you
A car of mass 250 kg and volume of 64 m3 is submerged in s river. A crane is used to pull the car from river with the help of a rope. Calculate the tension in th rope.
3- If F = 1x, F = xi, a = wk,, the centrifugal force is equal to a: mw²xî ------- b: -mw²xk c: mw²x k a: 4 d: -mw²xî e: None of them Ś
A modern wind turbine of (100 m) hub height works at an ideal conditions. Find the Q3 mechanical power of that wind turbine per unit area.
Calculate the total force exerted on the outside of a circular submarine window of diameter 30-em at a depth of 1200 meters.
An impermeable membrane (See figure above) is placed at the bottom of a U-tube, then equal amounts of water and oil are poured at each limb of the tube such that the height on both sides reads 16.5cm. If the impermeable membrane is removed, calculate the height difference in cm of the U-tube, assuming a uniform cross-sectional area of the U-tube, and given that the specific gravity of oil is 0.843.
I want solution of this question with all steps. Big Thumb for you
A hydraulic press is used to raise an 80 kN cargo truck. If oil of specific gravity 0.82 acts on the piston under pressure of 10Mpa. What is the diameter of piston required?
QV: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.