Answered: 1. A 2000/200V, 20kVA transformer has…

1. A 2000/200V, 20kVA transformer has 66 turns in the secondary. Calculate: (a) Primary turns (b) primary and secondary full load currents. Is the transformer step up? Why?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.5MCQ: For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is...

See similar textbooks

Related questions

Q: Obtain the waveform of output states Q and Q for the D latch when the input condition as in Figure 2…

A: The latch is a device that stores a bit of data in it. It is a level-triggered device and it changes…

Q: The unity feedback system shown Figure P9.1 with G(s): = K(s+6) (s+2)(s+3)(s+5) controller so that…

A: The Given Feedback system is unity. The Given Transfer function is Gs=Ks+6s+2s+3s+5

Q: 2) Compute the convolution y[n] = x[n] *h[n] of the following pairs of signals: a) x[n] = aru[n],…

A: Given :

Q: given figure, ca ulate ssuming в о ur answer A Bo R1 2002 d the current flowing through R3 assuming…

Q: The intrinsic impedance of the medium whose, σ = 0, ε, = 4, μ, =1 40 ΠΩ 9Ω 120 ΠΩ 60 ΠΩ

Q: 1. Two resistors, each of magnitude R1 = 100Ω and R2 = 200Ω If the two resistors are connected to a…

Q: How much current is flowing through the circuit?

A: from the previous solution, VD1=5 VVD2=-1.7 V The simplified circuit is drawn below:

Q: In a tansistor, I = 70 mA and I = 70.2 mA. The value of ß is Select one: a. 50 b. 350 O c. about 1 O…

A: Given: Collector current, IC=70 mA Emitter current, IE=70.2 mA

Q: When a pentavalent impurity is added to a pure semiconductor, it becomes 1. An insulator 2. An…

Q: Refer to attached schematic diagram. Solve for Total Resistance, REQ If a supply voltage of 10 V is…

Q: A semiconductor is formed by ......... bonds.

A: The correct option along with the explanation is provided in the following section.

Q: Obtain the impedance diagram with all impedance including the load impedance marked in per unit for…

Q: In the given circuit, what is the value of the collector current (IC) if the BJT is made of Silicons…

A: Given circuit, BJT is made of silicon.

Q: ED TO WRITE STORIES. DON'T COPY. OTHERWISE I WILL GIVE YOU DOWNVOTE. 42) What is the function of…

A: MCB (Miniature Circuit breaker) Function of MCB- The main function of MCB is to protect instrument…

Q: Two resistors have color codes of yellow, violet, gold, gold and green, black, brown, gold…

A: Q1) Given data Colour code of the first resistor (R1): Yellow, Violet, Gold, Gold Colour code of the…

Q: For unity feed back system with a forward transfer function K G(s) = s(s+50)(s + 120) Use frequency…

A: A system's steady-state reaction to sinusoidal inputs of different frequencies is referred to as its…

Q: 18. Two-Loop Circuit Find the currents Ij and Iz in the two- loop circuit in Fig. 6.7.7, when…

A: Given, V(t) = 60V R1=2Ω, R2=1Ω L1=5H, L2=1H

Q: 2000 25: 1:50 II Ideal Ideal 35 ΚΩ I want to find the average power delivered to the 5 k ohm…

A: The circuit diagram is shown below, Where,Vin =250∠0° Vrms

Q: In pulse amplitude modulation, a. Amplitude of the pulse train is varied b. Width of the pulse train…

A: The correct option along with the explanation is provided in the following section.

Q: refer to attached schematic diagram: The discharging time constant is than the charging…

Q: Can you explain the difference between these two forms? Like where the current is going, and how it…

A: In the first figure, the solar cell is in operating condition when the sun light strikes on it. So,…

Q: 9. Which of the following is correct about the power consumed by R₁ and R₂ connected in series if…

A: The solution is provided in the following section.

Q: A 132 KV line with 2 cm diameter conductors is built so that corona takes place if the line voltage…

Q: Design the following Boolean functionF(A,B,C,D) = ∑ (1,3,5,7,13, 15) using (8 x 1) MUX (B, C, D are…

A: The multiplexer can be used to design any Boolean expression by using the truth table derived for…

Q: PLEASE ANSWER ALL OF THIS!!! Direction: Round off the answers to three decimal places. a) What…

A: a) Given : Frequency range225 to 600 MHz find time period b) Given: S/N=3.2 FC=20 MHzFM=2.2…

Q: A t r a n s f o r m e r w i t h 3 0 p r i m a r y t u r n s i s c o n n e…

A: Given,Vp= 240 VNp= 30Vs=1440 VNs=?

Q: Why would an oscillator of the closed-loop model be expected toprovide a more stable rhythmic output…

A: Oscillators and their property: Oscillators are the circuit which are used to convert the DC voltage…

Q: Find the equivalent resistance. Please show work, thanks! 2 Ω I 6 Ω 4.3 Ω 25 V do 6 Ω S

Q: Two resistors R₁ and R2 (where R₁ > R₂) are connected in series to an ideal battery. Which of the…

Q: A. Find the energy stored in the capacitor and inductor in Fig. 3 8 mA 10 nF 3kn 2 MA O 12 V Fig 3…

Q: Question 37.a What would be the demand load for this branch circuit for the loads 1, 2, and 3? (Show…

A: The percentage represents the difference between the load that was actually connected during a…

Q: Sine wave is a a. Periodic signal b. Aperiodic signal c. d. Both a and c Deterministic signal

A: The correct option along with the explanation is provided in the following section.

Q: 7.2Ω THE 6V 8 Ω R₂ 12 Ω R3

Q: Find the total resistance in the figure shown below 10 ¡¯‚¯……… www www Your answer 10 the 50 Q…

Q: 2. Simplify the block diagram below. R(s) S²-45+4 S-2 S³ apples S+2 S²+45+4+ S²-4 C(s)

A: Given: Consider the following system: To find: Simplify the block diagram.

Q: Q.8 Current through 2 Ω resistor in the network shown is: SV (+ ΤΩ ΤΩ www www 1.Q ΙΩ Μ ΖΩ

A: Given data, Circuit diagram is given as,

Q: , R₁ 59. For the circuit shown below, ε = 50 V, and L= 2.0 mH. Find the values of 1₁ and 12 (a)…

Q: Identify the sensor connections as PNP (sourcing) and NPN (sinking). +DC LOAD +DC LOAD SENSOR -DC…

A: Observation: The First(LHS) schematic illustrates the following, Pure DC supply The given sensor…

Q: A DAC has a 10v range and 8 bits of resolution. What is the step size?

A: Given: A DAC has Voltage range, Vrange=10 V Number of bits, n=8

Q: Find it through i4 in the given circuit. Assume / = 20 A. 60 Ω 40 Ω ww The value of i₁ is The value…

A: Given,

Q: Consider the following circuit diagram. If each battery is labeled 10 V, 3Ω, then what is the strong…

A: The required parameter can be calculated by using the Kirchhoff's voltage law to the circuit.

Q: . Two wires A and B are both made of the same conductor material. The length of wire A is three…

Q: Which of the following is a characteristic of the feedback function? Select a Choice Below A B It is…

A: Given: Feedback function: Feedback function in a system. A feedback system compares the output…

Q: An audio signal represented by 60 sin 3000nt (Volts) modulates a 200 kHz carrier signal with…

Q: Mention and discuss the uncertainties affecting the power system operation and planning indices.

A: Uncertainty is associated with the massive power generation of the renewable energy. The renewable…

Q: 0 a) Compute 13-39 using 2's complement method on an 8-Bit adder/subtractor circuit. b) Convert the…

A: The solution of the following questions are

Q: A 10A current is lagging the voltage by 47° and a 12A current is lagging the voltage by 58°. What is…

A: Given: 10 A current lagging the voltage by 470 and 12 A current lagging the voltage by 580. We have…

Q: In the following circuit, find the power supplied by 10-V voltage source in Watt. Hint: Provide only…

A: Given:

Q: Gauss’s law can tell us how much charge is contained within aGaussian surface. Can it tell us where…

A: Gauss is used to determining the magnitude of the charge within the Gaussian surface. The net…

Q: A tuned LC circuits shown in Figure Q3 has an inductor of 1.0 nH and a variable capacitor with the…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

1. A 2000/200V, 20kVA transformer has 66 turns in the secondary. Calculate: (a) Primary turns (b) primary
and secondary full load currents. Is the transformer step up? Why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Why is it important to reduce the moisture within a transformer to acceptable levels during transformer installation?
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
An ideal transformer has no real or reactive power loss. (a) True (b) False
A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an autotransformer to step up the voltage from 2300 to 2530 volts (a) Draw a schematic diagram of this arrangement, showing all voltages and currents when delivering full load at rated voltage. (b) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of this kVA rating is transformed by magnetic induction? (C) The following data are obtained from tests carried out on the transformer when it is connected as a two-winding transformer: Open-circuit test with the low-voltage terminals excited: Applied voltage =230V, input current =0.45A, input power =70W. Short-circuit test with the high-voltage terminals excited: Applied voltage =120, input current =4.5A, input power =240W. Based on the data, compute the efficiency of the autotransformer corresponding to full load, rated voltage, and 0.8 power factor lagging. Comment on why the efficiency is higher as an autotransformer than as a two-winding transformer.
With the American Standard notation, in either a Y-or-Y transformer, positive- sequen quantities on the high-voltage side shall lead their corresponding quantities on the low-voltage side by 30. (a) True (b) False
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.