PLEASE ANSWER ALL OF THIS!!! Direction: Round off the answers to three decimal places. a) What should be the period of the multivibrato of a pulse-averaging discriminator if its input is an FM wave that has a frequency range of 225 to 600MHz? b) An FM receiver has an input S/N of 3.2. The carrier frequency, modulating frequency, and maximum allowed deviation are 20MHz, 2.2kHz and 5.6kHz respectively. Find the frequency deviation caused by the noise and the output S/N. c) Draw the frequency spectrum of a 190MHz carrier deviated by 25kHz by a 9.8kHz modulating signal. d) What is the difference between the bandwidth calculated from the two methods (Carson's and Bessel) for the signal described

PLEASE ANSWER ALL OF THIS!!! Direction: Round off the answers to three decimal places. a) What should be the period of the multivibrato of a pulse-averaging discriminator if its input is an FM wave that has a frequency range of 225 to 600MHz? b) An FM receiver has an input S/N of 3.2. The carrier frequency, modulating frequency, and maximum allowed deviation are 20MHz, 2.2kHz and 5.6kHz respectively. Find the frequency deviation caused by the noise and the output S/N. c) Draw the frequency spectrum of a 190MHz carrier deviated by 25kHz by a 9.8kHz modulating signal. d) What is the difference between the bandwidth calculated from the two methods (Carson's and Bessel) for the signal described

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Make an essay about "how filter circuits for AC and DC power supply works"
Can you please answer the question
How many AM stations can be accommodated in a 150 kHz bandwidth if the highest modulating signal frequency is 10 kHz?
hiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddenhiddencan you answer d) Sketch the AM wave and label the maximum and minimum voltage of the signal.letter d only.
1) From the plots, what is the frequency of the input signal (in samples as well as radians)? 2) From the plots, what is the frequency of the output signal (in samples and radians)? 3) What does echo do to the magnitude and phase spectra?
An AM waveform has a maximum span of 7.5V while minimum span of 2.5V. Determine the modulation index and the transmission efficiency.
01 for the signal that is shown in the figure below A) plot the amplitude spectrum B) Determine the total power C) Find the value of (n) such that the power reaches %50 of the total power
1. Calculate the total power of AM signal (par-A). 2. Calculate the bandwidth of AM signal (part-A). 3. Draw the spectrum of AM signal (part-A). DC Vmax Vmin m 3v 1.4 0.25 0.7 2v 1 0 1 1v 0.8 -0.36 1.94
Explain Frequency Modulation (FM), Amplitude Modulation and Phase Modulation (PM) signal in time domain, frequency domain. Answer in paragraph form
5 a) Consider the sample sequence (5000, 5000, 5000, 5000, -5000, -5000, -5000, -5000}. These are samples of a square wave with a period of eight samples or 1ms at 16 KHz sampling frequency. What are the sinusoidal frequencies in the output waveform?
2. Write an OCTAVE program to plot the signal given below. P- Pmax Sin(21Ift); where Pmax= 10 MW, -60 Hz. %3D Find out time period and verify it with graph. Assume necessary data.
Deter mine the modulation and instantenous frequency of signal $ (t) = A Cos ClotT tīt') at t=0 %3D