What type of waveform is produced from a bridge rectifier circuit with an open diode? Oa. Half-wave output equal to Vsec- 1.4 O b. Half-wave output equal to Vsec- 0.7 Oc. Full-wave output equal to Vsec- 1.4 Od. Full-wave output equal to Vsec– 0.7 QUESTION 14 To maintain a constant voltage supplied to the load, we can use Oa. A high-resistance voltage divider Ob. Either a Zener diode or an IC regulator OC. A Zener diode Od. An IC regulator

What type of waveform is produced from a bridge rectifier circuit with an open diode? Oa. Half-wave output equal to Vsec- 1.4 O b. Half-wave output equal to Vsec- 0.7 Oc. Full-wave output equal to Vsec- 1.4 Od. Full-wave output equal to Vsec– 0.7 QUESTION 14 To maintain a constant voltage supplied to the load, we can use Oa. A high-resistance voltage divider Ob. Either a Zener diode or an IC regulator OC. A Zener diode Od. An IC regulator

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply voltage and the output voltage waveform. b) Explain why there is no negative output voltage even without freewheeling diode. c) Derive the expression for average output voltage.
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop.
Write the following for a half wave controlled rectifier with RL load and freewheeling diode a) Draw the circuit diagram, supply voltage and the output voltage waveform. b) Explain if there is no freewheeling diode what would be the output voltage. c) Explain the difference in the output voltage with and without the freewheeling diode
For the full wave rectifier circuit shown, if vs=15sin(120nt) (V), R=10052, assuming constant voltage drop with VDo=0.7 J. 1. LDraw clearly and accurately with details the following waveforms: Source voltage (vs), load voltage (v.) 2. Describe in details the operation of the circuit indicating which diodes will be ON which ones will be OFF and state clearly the condition at which each diode will be ON or be OFF. 3. Calculate the mean load current (IRmean) given Vmean=2Vp/T. 4. Calculate the PIV. ac line Us voltage D2 Maximum size for new files: 10MB, maximum attachments: 2 Files 79 CE255/EE255 (01)-..
A three-phase half wave rectifier has a supply of 150V/phase. Determine the mean load voltage and the required diode rating, assuming the load current is level at 25A. Assume each diode has a volt-drop of 0.7V.
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.