1- For a system with the transfer function Y(s) 2s³ - 12 U(s) 4s5 S3 + 4s 10 The state matix is ---------- and the input matrix is--- 2- For a system with the transfer function R(s) The input matrix is 3- For the below block diagram the forward transfer function is while the feedback ratio is + G3 The input matrix is G₁ Y(s) U(s) H1 (1 + s²)-1 while the state matrix is 4- A system with a dynamic equation: ‒‒‒‒‒‒‒‒‒‒‒‒ G₂ H₂ + + →→C(s) 2x(t) + 10x(t) = 3u(t) --------- and the poles of the system are

1- For a system with the transfer function Y(s) 2s³ - 12 U(s) 4s5 S3 + 4s 10 The state matix is ---------- and the input matrix is--- 2- For a system with the transfer function R(s) The input matrix is 3- For the below block diagram the forward transfer function is while the feedback ratio is + G3 The input matrix is G₁ Y(s) U(s) H1 (1 + s²)-1 while the state matrix is 4- A system with a dynamic equation: ‒‒‒‒‒‒‒‒‒‒‒‒ G₂ H₂ + + →→C(s) 2x(t) + 10x(t) = 3u(t) --------- and the poles of the system are

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Six similar attenuators are used in an audio design and are linked in a cascade. The total attenuation is 80 decibels. The first section of the attenuator circuit has a 20 mV input. Determine (i) the attenuation in decibels provided by each individual attenuation stage, (ii) the output in volts of the final stage (iii) the output in volts of the fifth stage.
The scale multiplier (factor) of a basic integrator is – 1/RC Select one: True False
Q2) For the mechanical system in figure (1). Drive the transfer function Y(s)/F(s) KI f M K2
A type II compensator implementation for the above Buck converter is shown below. Ce2 Vout Cet HH Ret Vctrl R2 E/A Vset What should be the voltage Vref in the above type II compensator to produce 5V DC output if R# = 4k and R2=1k. а. Vet b. Write the small signal gain equation (-ctrl) between Vetrl and Vout- out с. Does R2 present in the above gain equation. Please add some explanation. d. How many poles and how many zeros are produced by this type II compensator?
1-Drive the formula for ZOH. 2-What happens when the sampling rate is less than 2 Hz? 3- Show the effect of sampling time on the characteristic of ZOH. digital to analog converter
Determine the required values of R1, R2, Rc, and RE. Also, determine the expected output voltage if the input voltage is equal to 0.001 Vrms. GIVEN: Zi = 1145.66 ohms Zo = 3.3 Kohms Beta = 80 Vcc = 20V R1 + R2 = 43.7 Kohms Av = 167.43 Ai = 58.13
I designed a summing amplifier that could amplify a 1mV sinusoid (Vina) into a sinusoid with 1V amplitude and 3.5V offset. The value for R1a is 1k ohms, for R1b is 1mega ohms, R2 is 1 mega ohms, and Vin b is -3.5V. What is the input offset voltage?
For the mechanical system in figure (4). Drive the transfer functionY(s)/F(s)
-60m It is the the maximum frequency that an op-amp may operate which depends on both the bandwidth (BW) and slew rate (SR) parameters of the op-amp. O Cut-off frequency O Unity Gain Bandwidth O Unity Gain Frequency O Maximum Signal Frequency
II. K type thermocouple having a range of 0 – 350 °C and a sensitivity of 40 µV/°C. The signal is connected to an instrumentation amplifier before interfacing it with 5V analog to digital converter. Design a suitable instrumentation amplifier circuit. Vsupply thermocouple Vout Instrum. op Amp ADC -Dout
3ZK If the output of a differentiator op-amp is -cos(wt) then the input is a.-sin (wt) b.none of the above c.sin (wt) d.cos (wt)
Problem C It is desired to have a gain of 20 for frequencies up to 180 kHz. Determine the minimum unity gain frequency specification for the op amp. The gain should be within at least 98% Vsig Rin + Rf Vcc/-Vcc +12v/ -12V Vout