1 Choose the correct letter, A, B, C or D. Estimate the number of filters required for water treatment if the flow rate=1.4 m³/s, the design loading rate to the filter is 200 m³/d.m², and the surface area of each filter= 80 m². One of the following media has the lowest specific gravity in the filter body: What is representing the total alkalinity of water sample, if the pH of water <<=10.33 A 7 B HCOS 10 Garnet Anthracite CO₂ C 5 Sand H₂CO3 D 12 Gravel A+B

1 Choose the correct letter, A, B, C or D. Estimate the number of filters required for water treatment if the flow rate=1.4 m³/s, the design loading rate to the filter is 200 m³/d.m², and the surface area of each filter= 80 m². One of the following media has the lowest specific gravity in the filter body: What is representing the total alkalinity of water sample, if the pH of water <<=10.33 A 7 B HCOS 10 Garnet Anthracite CO₂ C 5 Sand H₂CO3 D 12 Gravel A+B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following diagram illustrates the operation of a rapid sand filter. Washwater storage tank Water level while filtering E A From coagulation larification basi 2 00 Water level while washing Filter rate controller E Lateral drain Filtered water storage tank Main drain Washwater drain The Valve D is to O 1) Control influent water from sedimentation tanks O2) Discharge dirty backwash water 3) Discard the initial filtered water after backwashing and resuming filtration 4) Control the clean backwash water 5) None of the above B3 Seal Sand Gravel 0 0 0 0 0 Caf Bottom of washwater trough Washwater rate controller
If (Qr/Q=120 percent of discharge), effluent BOD concentration=80ppm, volume of filter =825m3 , discharge =50L/sec , The influent BOD concentration equal: Choose one: a. 277.89 b. 277.2 c. 276 d. 275
(c) A filter has a head loss of 0.30 m when clean and 1.30 m after 24 hours of filtration at a rate of 1.5l/s. . Estimate the following if the filtration rate is changed to 2 l/s i. head loss immediately after backwash ii. 10 hours later
A filter press with an effective filtering area between 350m^2 operates constantly maintaining a pressure difference of 35000Pa. The viscosity of the fluid (water with milk solids) was measured at 0.002Kg/Ms and the following data is obtained: (Data image) Considering that the density of milk solids on average is 200Kg/m^2, calculate filtration velocity at t=120m
The following diagram illustrates the operation of a rapid sand filter. Washwater storage tank Water level while filtering E B A From coagulatin larifica on basi Filtrate controller Bottom of washwater trough Washwater rate controller Lateral drain Seal Filtered water storage tank Main drain. Wasitwater drain During filtration cycle, the valves A, B, C and E open/close as follows: O 1) A and B open and C and E close 2) A and B close and C and E open 3) A and C open and B and E close 4) A and E open and B and C close 5) A and C close and B and E open U Water level while washing Sand Gravel 000 MANSKER
9. In the design of filter material ,if (D15)s =0.06 mm then (D15)f must be Less than 0.06 mm Equals to 0.06 mm Less than 0.3 mm d) More than 03 mm
N 5)( rat ala SIL O 23-A) An activated sludge system is to be used for treatment of 10000 m/day of municipal wastewater. A rimary clarification, the value of BOD, is 150 mg/l, and it is desired to have not more than 5 mg/l. in. ffluent. Assume that Y- 0.5; K, 0.05/day; and ML.VSS-3000 mg/l; Return sludge concentration 10 ng/L. 0 10 days. Determine: Treatment efficiency and the volumetric organic loading. 3) Microorganism ratio 5) The quantity of sludge that must be wasted each day i 2) Reactor volume and detention time. 4) the recycle ratin
a) Determine the total GMF surface area required to filter a volumetric flow rate of 10.0 MGD at a filtration rate of 4.0 gpm/ft2 . Divide the total surface area into an appropriate number of filter cells and determine the planar dimensions if square cells are used. Determine the percentage of the filtered water that will be used for backwashing under the following conditions, Each filter cell is backwashed once every 24 hours • Backwashing rate of 20.0 gpm/ft2 • Each cell is backwashed for a duration of 10 minutes Also determine the filtration rate through the remaining filter cells when one cell is removed from service for backwashing.
b <: I 1 I (mm/hr) = at + 12 where it is accumlated in filtration time (min) use the below Data to estimate Dein fretration rate. after (one) hour, an'any w/I) (t) min (D) Accumlation infiltration : depth (mm) 30 ( رام 150 80
Mixing (non reacting fluids), Electric circuits. Problem#1 A large tank holds 300 gallons of brine solution with 40 pounds (lb) of salt. A concentration of 2 lb/gallon is pumped in a rate of 4 gal/min. The concentration leacving the tank is pumped put at a rate of 3 gal/min. How much salt is in the tank after 12 minutes? Answer: 126.12 lb of salt
Problem 4In water and wastewater treatment processes a filtration device may be used to remove water from the sludgeformed by a precipitation reaction. The initial concentration of sludge from a softening reaction is 20,000 mg/Land the volume of sludge is 100 m3. After filtration the sludge solids concentration is 350,000 mg/L. Assume thatthe sludge does not change density during filtration, and there is no accumulation of sludge in the filtrationdevice. Using the mass balance method, determine the volume of sludge after filtration.
Design a trickling filter system for BOD removal without the nitrification requirement, to treat municipal wastewater with an average flow of 200 m3/d (Qin) and influent BOD of 200 mg/L and Ammonium (NH4-N) of 42 mg/L. Make appropriate assumptions and use the design indicators for plastic media filters as given below. What are the possible effects of the peak flow of 1.5 times occurring once in a month? Volumetric loading rate (Bv)= 0.5 kgBOD/m3.d Volumetric loading rate for NH4-N (Bv, NH4-N)= 0.2 kgNH4-N/m3.d Hydraulic loading rate (qh= Q/AR)= 1.2 m/h Recirculation ratio (Qr/Qin) = 0.5