1) A sinusoidal signal of 500 mV and 1 kHz from peak to peak is given as the input signal from the function generator. a) Calculate the voltage gain of the circuit in Figure 1. b) What is the phase relationship between input and output signals? (Assume ß = 50 and VBE = 0.4 V) VcC 12V RE 10kO RL 56kO Vout 10µF 10uf BD139 Vin RB1 >2.2k0 RB2 $0.56kO 500 mVpp 1 kHz Figure 1 一

1) A sinusoidal signal of 500 mV and 1 kHz from peak to peak is given as the input signal from the function generator. a) Calculate the voltage gain of the circuit in Figure 1. b) What is the phase relationship between input and output signals? (Assume ß = 50 and VBE = 0.4 V) VcC 12V RE 10kO RL 56kO Vout 10µF 10uf BD139 Vin RB1 >2.2k0 RB2 $0.56kO 500 mVpp 1 kHz Figure 1 一

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5 Listed are some of the uses of capacitors except: A. couples AC B. bypassing a shunt load C. signal amplification D. filters pulsating DC
R1 Vi 1kO Di IN4148 D2–1N4148 5V Vo -5V -3V Figure 1 a)Draw a simplified circuit for positive and negative cycle then calculate the output voltage (Vo) for both cycles. b)Sketch the output waveform, Vo for the circuit.
A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis is 1 unit=4 v; determine the frequency of the sine wave and plot the waveform if the same is applied to input of a full wave rectifier.
What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform A (b) 44444 F -V O Unipolar O Bipolar 000
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
CIRCUIT DIAGRAM : D1 IÑ4001 AC Source RL 1K Q VOUT PROCEDURES : 1. Construct the half-wave rectifier circuit as shown. 2. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the formula: 3. 4. Vp-p Vp-p P-P VRMS 2.828
A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The load is purely resistive of value 52. The DC and RMS output voltages are respectively equal to: Secondary 太D太D,太D, 太D。太De太D, b. Select one: O a. 180V, 240.2V O b. 514.6V, 515.04V O c. 180V, 197.2V O d. 220V, 249.2V
C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. C2 (ii). A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 40 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3 cm and the peak to peak distance is 5.6 cm. Determine the following: The frequency is The magnitude of the sine voltage is The amplitude is The R.M.S voltage is
Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Thyristor Crout Probe Pulse Generator VC, pulses Probe Scope Thy Orso v Joad O R: 1 The output voltage across R is depicted in 0.5 0.0- b) 0.2 0.0 d)
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
The input to a full-wave rectifier is 20 V AC (RMS). The load resistor is 20 ohms and rectifier losses are 4W. The ripple factor of the rectifier is: O A. 0.96 OB. 0.33 O C. 0.48 O D. None of the other choices are correct O E. 0.75
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1